cue(4) [freebsd man page]

CUE(4)							   BSD Kernel Interfaces Manual 						    CUE(4)

NAME

     cue -- CATC USB-EL1210A USB Ethernet driver

SYNOPSIS

     To compile this driver into the kernel, place the following lines in your kernel configuration file:

	   device uhci
	   device ohci
	   device usb
	   device cue

     Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):

	   if_cue_load="YES"

DESCRIPTION

     The cue driver provides support for USB Ethernet adapters based on the Computer Access Technology Corporation's USB-EL1210A chipset.

     The USB-EL1210A supports a 512-bit multicast hash filter, single perfect filter entry for the station address and promiscuous mode.  Packets
     are received and transmitted over separate USB bulk transfer endpoints.

     The CATC chipset supports only 10Mbps half-duplex mode, hence there are no ifmedia(4) modes to select.

     For more information on configuring this device, see ifconfig(8).

HARDWARE

     The cue driver supports CATC USB-EL1210A based USB Ethernet adapters including:

     o	 Belkin F5U011/F5U111
     o	 CATC Netmate
     o	 CATC Netmate II
     o	 SmartBridges SmartLink

DIAGNOSTICS

     cue%d: watchdog timeout  A packet was queued for transmission and a transmit command was issued, however the device failed to acknowledge the
     transmission before a timeout expired.

     cue%d: no memory for rx list  The driver failed to allocate an mbuf for the receiver ring.

SEE ALSO

     arp(4), netintro(4), ng_ether(4), ifconfig(8)

HISTORY

     The cue device driver first appeared in FreeBSD 4.0.

AUTHORS

     The cue driver was written by Bill Paul <wpaul@ee.columbia.edu>.

BSD
								   July 16, 2005							       BSD

CUE(4)							   BSD Kernel Interfaces Manual 						    CUE(4)

NAME

     cue -- CATC USB-EL1210A USB Ethernet driver

SYNOPSIS

     To compile this driver into the kernel, place the following lines in your kernel configuration file:

	   device uhci
	   device ohci
	   device usb
	   device cue

     Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):

	   if_cue_load="YES"

DESCRIPTION

     The cue driver provides support for USB Ethernet adapters based on the Computer Access Technology Corporation's USB-EL1210A chipset.

     The USB-EL1210A supports a 512-bit multicast hash filter, single perfect filter entry for the station address and promiscuous mode.  Packets
     are received and transmitted over separate USB bulk transfer endpoints.

     The CATC chipset supports only 10Mbps half-duplex mode, hence there are no ifmedia(4) modes to select.

     For more information on configuring this device, see ifconfig(8).

HARDWARE

     The cue driver supports CATC USB-EL1210A based USB Ethernet adapters including:

     o	 Belkin F5U011/F5U111
     o	 CATC Netmate
     o	 CATC Netmate II
     o	 SmartBridges SmartLink

DIAGNOSTICS

     cue%d: watchdog timeout  A packet was queued for transmission and a transmit command was issued, however the device failed to acknowledge the
     transmission before a timeout expired.

     cue%d: no memory for rx list  The driver failed to allocate an mbuf for the receiver ring.

SEE ALSO

     arp(4), netintro(4), ng_ether(4), ifconfig(8)

HISTORY

     The cue device driver first appeared in FreeBSD 4.0.

AUTHORS

     The cue driver was written by Bill Paul <wpaul@ee.columbia.edu>.

BSD
								   July 16, 2005							       BSD