yellowfin-diag(8) [debian man page]
YELLOWFIN-DIAG(8) System Manager's Manual YELLOWFIN-DIAG(8) NAME
yellowfin-diag - EEPROM setup and diagnostic program for Ethernet cards based on the "Yellowfin" G-NIC-I chip. SYNOPSIS
yellowfin-diag [options] DESCRIPTION
yellowfin-diag is a program that you can use to diagnose problems with Ethernet cards based on the "Yellowfin" G-NIC-I or Symbios 53c885 chip. OPTIONS
These programs follow the usual GNU command line syntax, with long options starting with two dashes (`-'). A summary of options is included below. -h, --help Show summary of options. -V, --version Show version of program. -v, --verbose Verbose mode. -q, --quiet Be very unverbose. -# <cardnum> Use card number <cardnum>. -a, --show_all_registers Print all registers. -e, --show-eeprom Dump EEPROM contents to stdout. -E, --emergency-rewrite Re-write a corrupted EEPROM. -p, --base-address <port> Specify port to use. -A, --Advertise <mediaype> Advertise media type. Valid Options are: 10baseT, 100baseT4, 100baseTx, 100baseTx-FD, 100baseTx-HD, 10baseT-FD and 10baseHD. -F, --new-interface <interface> Interface number. Options that make sense are: 10baseT, 10base2, AUI, 100baseTx, 10baseT-FDX, 100baseTx-FDX, 100baseT4, 100baseFx, 100baseFx-FDX, MII and Autosense. -H, --new-hwaddress <address> Set card to a new hardware address. -m, --show-mii Dump MII management registers. -R, --reset Reset the transceiver. -T, --test Do register and SRAM test. -w, --write-EEPROM <values> Write to the EEPROMS with the specified values. Do not use this, if you do not know what you do! -f, --force-detection Try to identify the card, even if it is active. -t, --chip-type <card> Explicitly set the chip. To get all valid numbers, run yellowfin-diag with the options '-t -1'. SEE ALSO
mii-diag(8) AUTHOR
yellowfin-diag was written and is still maintained by Donald Becker <becker@scyld.com>. This manual page was written by Alain Schroeder <alain@debian.org>, for the Debian GNU/Linux system (but may be used by others). February 18, 2002 YELLOWFIN-DIAG(8)
Check Out this Related Man Page
EPIC-DIAG(8) System Manager's Manual EPIC-DIAG(8) NAME
epic-diag - EEPROM setup and diagnostic program for SMC EtherPowerII ethernet cards and others. SYNOPSIS
epic-diag [options] DESCRIPTION
epic-diag is a program that you can use to diagnose problems with ethernet cards based on the SMC83C170 series EPIC/100 chip, as used on the SMC EtherPowerII boards. OPTIONS
These programs follow the usual GNU command line syntax, with long options starting with two dashes (`-'). A summary of options is included below. -h, --help Show summary of options. -V, --version Show version of program. -v, --verbose Verbose mode. -q, --quiet Be very unverbose. -# <cardnum> Use card number <cardnum>. -a, --show_all_registers Print all registers. -e, --show-eeprom Dump EEPROM contents to stdout. -E, --emergency-rewrite Re-write a corrupted EEPROM. -p, --port-base <port> Specify port to use. -A, --Advertise <mediaype> Advertise media type. Valid Options are: 10baseT, 100baseT4, 100baseTx, 100baseTx-FD, 100baseTx-HD, 10baseT-FD and 10baseHD. -F, --new-interface <interface> Interface number. Options that make sense are: 10baseT, 10base2, AUI, 100baseTx, 10baseT-FDX, 100baseTx-FDX, 100baseT4, 100baseFx, 100baseFx-FDX, MII and Autosense. -H, --new-hwaddress <address> Set card to a new hardware address. -m, --show-mii Dump MII management registers. -R, --reset Reset the transceiver. -T, --test Do register and SRAM test. -w, --write-EEPROM <values> Write to the EEPROMS with the specified values. Do not use this, if you do not know what you do! -f, --force-detection Try to identify the card, even if it is active. -t, --chip-type <card> Explicitly set the chip. To get all valid numbers, run epic-diag with the options '-t -1'. SEE ALSO
mii-diag(8) AUTHOR
epic-diag was written and is still maintained by Donald Becker <becker@scyld.com>. This manual page was written by Alain Schroeder <alain@debian.org>, for the Debian GNU/Linux system (but may be used by others). February 18, 2002 EPIC-DIAG(8)