Suppose I assign these variables:
n=5
row=n
let col=n/2
val=17
let table$row=val
I want to print the last variable. How do I do that? I have tried:
echo ${table$row}
This is the error message:
ksh: ${table$row}: bad substitution (6 Replies)
Hello all,
I have been trying to find any data that states what platform would garner better overall performance in an Oracle Cluster.
The scenario:
This is a high traffic e-commerce site with IIS and Commerce server on the front end. The backend consists of a Sun Solaris hardware/software... (7 Replies)
HI folks. I am developing a protocol and I need to bind to an IP address that is not configured to my machine. The problem is with bind(). The sysctl system call seamed to overcome the problem of bind if you set the proc/sys/net/ipv4/ip_nonlocal_bind flag. Although I tryed to set the flag either... (7 Replies)
Hello everyone. I'm trying to setup two A1000s connected to a single host w/ a dual port adapter. The host is a V480.
Do I need to have thesame firmware version on both controllers for the A1000s? If so, where can I download the latest and greatest firmware? I tried to google for it and... (8 Replies)
We get the error "NO HARD Disks found" while installing Solaris 10 (latest-6/06) on Poweredge 2950.
We found that the LSISAS1068 driver is needed for this. But the provision is given only to install the driver using the floppy (in downloads site). But we dont have a floppy drive in our system... (12 Replies)
Do you know how do I make my solaris 8 detect the storEDGE A5000?.
I have problem making it recognise, without that I cannot install VxVM.
Any ideas? (7 Replies)
Hello Experts,
I am using E250 on that solais 10 5/08 installed. I am unable to see disks. I connected 2 disks in that storage of 18gb each. When I run format command it is showing that 2 disks one is operating system and another one is 6MB. I checked probe-scsi and probe-scsi-all at ok... (6 Replies)
I am sys admin for many servers running unix (solaris, HP, Linux) and also some windows server and solaris x86
I want to know what leading software is out there whether it be freeware, shareware or commercial that can do things listed:
Performance monitoring (hardware/software, disk usage,... (7 Replies)
I am trying to connect D1000 storedge with my sun blade 1500 and i am getting the following error when booting the system.
Oct 13 22:21:56 brampton rpcbind: rpcbind terminating on signal.
Oct 13 22:22:02 brampton syseventd: SIGHUP caught - reloading modules
Oct 13 22:22:02 brampton... (9 Replies)
So I have a Networking class at my university that involves learning the basic commands of unix (i.e. Chmod, cat, cp, ls, mv, rm, mkdir, rmdir, pwd, etc) and my professor had us download and install Solaris and PuTTY as a means of...I suppose practicing using/executing commands. However due to... (7 Replies)
Hey guys I am new at Solaris 10, and I'm having a open error on
/dev/dsk/c1t1d0s6, when booting.
We have a Sunfire v240 running Solaris 10, which is connected to a Storedge 3320, via SCSI.
Any help, is appreciated (14 Replies)
Hey people people,
I am a new grasshopper willing to learn from the masters. I type a lot when I am nervous!
I have pulled tons of info off here in the last week concerning awk. I know nothing about awk, I mean nuthin. I have started work as the guy below the lowest man on the... (8 Replies)