SBP_TARG(4) BSD Kernel Interfaces Manual SBP_TARG(4)NAME
sbp_targ -- Serial Bus Protocol 2 (SBP-2) Target Mode devices driver
SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file:
device sbp_targ
device firewire
device scbus
device targ
Alternatively, to load the driver as a module at boot time, place the following lines in loader.conf(5):
firewire_load="YES"
cam_load="YES"
sbp_targ_load"YES"
DESCRIPTION
The sbp_targ driver provides support for SBP-2 target mode. This driver is supposed to work with cam(4), targ(4) and firewire(4). You also
need to use scsi_target(8), which can be found in /usr/share/examples/scsi_target, to provide actual devices.
EXAMPLES
# mdconfig -a -t malloc -s 10m
md0
# scsi_target 0:0:0 /dev/md0
(Assuming sbp_targ0 on scbus0)
SEE ALSO cam(4), firewire(4), targ(4), camcontrol(8), fwcontrol(8), kldload(8), scsi_target(8)AUTHORS
The sbp_targ driver was written by Hidetoshi Shimokawa.
BUGS
This driver is currently under development. It does not work correctly in multi-initiator environments or after the bus topology has been
changed.
BSD November 7, 2003 BSD
Check Out this Related Man Page
SBP_TARG(4) BSD Kernel Interfaces Manual SBP_TARG(4)NAME
sbp_targ -- Serial Bus Protocol 2 (SBP-2) Target Mode devices driver
SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file:
device sbp_targ
device firewire
device scbus
device targ
Alternatively, to load the driver as a module at boot time, place the following lines in loader.conf(5):
firewire_load="YES"
cam_load="YES"
sbp_targ_load"YES"
DESCRIPTION
The sbp_targ driver provides support for SBP-2 target mode. This driver is supposed to work with cam(4), targ(4) and firewire(4). You also
need to use scsi_target(8), which can be found in /usr/share/examples/scsi_target, to provide actual devices.
EXAMPLES
# mdconfig -a -t malloc -s 10m
md0
# scsi_target 0:0:0 /dev/md0
(Assuming sbp_targ0 on scbus0)
SEE ALSO cam(4), firewire(4), targ(4), camcontrol(8), fwcontrol(8), kldload(8), scsi_target(8)AUTHORS
The sbp_targ driver was written by Hidetoshi Shimokawa.
BUGS
This driver is currently under development. It does not work correctly in multi-initiator environments or after the bus topology has been
changed.
BSD November 7, 2003 BSD
Friends I'm facing a big problem trying to extend the netfilter. Somone please help me with your quick reply (any hint) as I've to meet a deadline.
My problem is that I've written a new netfilter target module and its corresponding userspace program for iptables to change the packet type of a... (0 Replies)
I have a Microdia web cam. Some times it won't work if and only if there is a "HV7131R image sensor detected" statement in the boot up.
In this case when I try to get a .png snapshot all I get is a frame full of what appears to be white noise only it is mostly green.
Here is the command I am... (0 Replies)
I have been reading prep questions for my second unix academy exam, and there's a nuance, I'm not sure I understand it correctly.
I've been under impression from my readings of book by Evi Nemeth and from unix academy DVDs I've been watching, that kernel's modules are drivers. I think of it, as... (25 Replies)
Hi everyone,
I am not sure if I understand how mdadm --create /dev/md0 --level=container works?
A device called /dev/md0 appears in /proc/mdstat but I am not sure how to use that device?
I have 2 blank drives with 1 500GB partition on each. I would like to setup mirroring, but not in the... (0 Replies)