scrobble-cli(1) [debian man page]

SCROBBLE-CLI(1) 					      General Commands Manual						   SCROBBLE-CLI(1)

NAME

       scrobble-cli - a last.fm submitter for portable devices

SYNOPSIS

       scrobble-cli [options]

DESCRIPTION

       scrobble-cli is a program to submit information about tracks which have been listened to from a portable music player to last.fm
       (previously known as Audioscrobbler).  scrobble-cli can read this information from .scrobbler.log files (i.e. produced by the open Rockbox
       firmware), from iPod databases, or from devices that use MTP (aka Plays for Sure).  In addition to this, scrobble-cli can adjust the
       date/time information relating to when the track was listened to before uploading.  This can be useful if your device is set to a different
       timezone to the machine you upload from.

OPTIONS

       This program follows the usual GNU command line syntax, with long options starting with two dashes (`-').  A summary of options is included
       below.

       -c, --playcounts
	      Remove the iPod "Play Counts" database file after submission.

       -d, --database
	      Submit information from an iPod database (requires -l)

       -h, --help
	      Show summary of options.

       -l, --location <path>
	      Filesystem location of the .scrobbler.log file, or the iPod database.  For .scrobbler.log this should be the path to, and including
	      the file name.  For iPods, this should normally be the mount point - (/iPod_Control/iTunes/iTunesDB is automatically appended to
	      this path).

       -m, --mtp
	      Submit from a MTP (aka Plays for Sure) device

       -n, --now
	      Recalculates the times each track was played before submission.  Automatically enabled if using a .scrobbler-timeless.log or MTP
	      device.

       -p, --password <password>
	      Last.fm account password

       -r, --recalc <datetime>
	      Recalculates the play time for each track.  <datetime> should be a UNIX timestamp.

       -t, --timestamp <offset>
	      Override the detected system timezone offset from UTC <offset> is the number of hours from UTC, i.e. +3, -4.5

       -u, --username <username>
	      Last.fm account username

       -v, --verbose <level>
	      Output verbosity level

       -w, --proxy_host <hostname>
	      Proxy hostname or IP address (requires -x)

       -x, --proxy_port <port>
	      Proxy port number (requires -w)

       -y, --proxy_user <username>
	      Username for proxy authentication

       -z, --proxy_pass <password>
	      Password for proxy authentication

WWW

       http://qtscrob.sourceforge.net

       This manual page was written by Robert Keevil <rkeevil@gmail.com>, and is licensed under version 2 of the GPL.

								 February 16, 2009						   SCROBBLE-CLI(1)

Check Out this Related Man Page

BSCAN(8)					     Network backup, recovery and verification						  BSCAN(8)

NAME

	bscan - Bacula's 'Scan tape'

SYNOPSIS

       bscan [options] bacula-archive

DESCRIPTION

       The  purpose  of  bscan is to read (scan) a Bacula Volume and to recreate or update the database contents with the information found on the
       Volume.	This is done in a non-destructive way. This permits restoring database entries that have been lost by pruning, purging,  deleting,
       or a database corruption problem.

       Normally, it should not be necessary to run the bscan command because the database is self maintaining, and most corrupted databases can be
       repaired by the tools provided by the database vendors.	In addition, if you have maintained bootstrap files during backups, you should	be
       able to recover all your data from the bootstrap file without needed an up to date catalog.

       bscan command.

OPTIONS

       A summary of options is included below.

       -?     Show version and usage of program.

       -b bootstrap
	      Specify a bootstrap file.

       -c config
	      Specify configuration file.

       -d nn  Set debug level to nn.

       -dt    Print timestamp in debug output.

       -m     Update media info in database.

       -D     Specify the driver database name (default: NULL)

       -n name
	      Specify the database name (default: bacula)

       -u username
	      Specify database username (default: bacula)

       -P password
	      Specify database password (default: none)

       -h host
	      Specify database host (default: NULL)

       -t port
	      Specify database port (default: 0)

       -p     Proceed inspite of I/O errors.

       -r     List records.

       -s     Synchronize or store in Database.

       -S     Show scan progress periodically.

       -v     Verbose output mode.

       -V volume
	      Specify volume names (separated by '|')

       -w dir Specify working directory (default from conf file)

SEE ALSO

       bls(8), bextract(8).

AUTHOR

       This manual page was written by Jose Luis Tallon <jltallon@adv-solutions.net>, for the Debian GNU/Linux system (but may be used by others).

Kern Sibbald							 26 November 2009							  BSCAN(8)

Linux and UNIX Man Pages

scrobble-cli(1) [debian man page]

Check Out this Related Man Page