diskseekd(1) [debian man page]
diskseekd(1) General Commands Manual diskseekd(1) Name diskseek, diskseekd - disk seek daemon; simulates Messy Dos' drive cleaning effect Note This manpage has been automatically generated from fdutils's texinfo documentation. However, this process is only approximative, and some items, such as cross-references, footnotes and indices are lost in this translation process. Indeed, these items have no appropriate rep- resentation in the manpage format. Moreover, only the items specific to each command have been translated, and the general information about fdutils has been dropped in the manpage version. Thus I strongly advise you to use the original texinfo doc. * To generate a printable copy from the texinfo doc, run the following commands: ./configure; make dvi; dvips fdutils.dvi * To generate a HTML copy, run: ./configure; make html A pre-made HTML can be found at: `http://www.tux.org/pub/knaff/fdutils' * To generate an info copy (browsable using emacs' info mode), run: ./configure; make info The texinfo doc looks most pretty when printed or as HTML. Indeed, in the info version certain examples are difficult to read due to the quoting conventions used in info. Description Several people have noticed that Linux has a bad tendency of killing floppy drives. These failures remained completely mysterious, until somebody noticed that they were due to huge layers of dust accumulating in the floppy drives. This cannot happen under Messy Dos, because this excuse for an operating system is so unstable that it crashes roughly every 20 minutes (actually less if you are running Windows). When rebooting, the BIOS seeks the drive, and by doing this, it shakes the dust out of the drive mechanism. diskseekd simulates this effect by seeking the drive periodically. If it is called as diskseek, the drive is sought only once. Options The syntax for diskseekd is as follows: diskseekd [-d drive] [-i interval] [-p pidfile] -d drive Selects the drive to seek. By default, drive 0 (`/dev/fd0') is sought. -i interval Selects the cleaning interval, in seconds. If the interval is 0, a single seek is done. This is useful when calling diskseek from a crontab. The default is 1000 seconds (about 16 minutes) for diskseekd and 0 for diskseek. -p pidfile Stores the process id of the diskseekd daemon into pidfile instead of the default `/var/run/diskseekd.pid'. Bugs 1. Other aspects of Messy Dos' flakiness are not simulated. 2. This section lacks a few smileys. See Also Fdutils' texinfo doc fdutils-5.5 03Mar05 diskseekd(1)
Check Out this Related Man Page
setfdprm(1) General Commands Manual setfdprm(1) Name setfdprm - sets user-provided floppy disk parameters Note This manpage has been automatically generated from fdutils's texinfo documentation. However, this process is only approximative, and some items, such as cross-references, footnotes and indices are lost in this translation process. Indeed, these items have no appropriate rep- resentation in the manpage format. Moreover, only the items specific to each command have been translated, and the general information about fdutils has been dropped in the manpage version. Thus I strongly advise you to use the original texinfo doc. * To generate a printable copy from the texinfo doc, run the following commands: ./configure; make dvi; dvips fdutils.dvi * To generate a HTML copy, run: ./configure; make html A pre-made HTML can be found at: `http://www.tux.org/pub/knaff/fdutils' * To generate an info copy (browsable using emacs' info mode), run: ./configure; make info The texinfo doc looks most pretty when printed or as HTML. Indeed, in the info version certain examples are difficult to read due to the quoting conventions used in info. Description setfdprm [-p] device media-description setfdprm [-c | -y | -n] device setfdprm is a utility that can be used to load disk parameters into the auto-detecting floppy devices and "fixed parameter" floppy devices, to clear old parameter sets and to disable or enable diagnostic messages. These parameters are derived from a media-description, see sec- tion Media description for more details. Without any options, setfdprm loads the device (for example `/dev/fd0' or `/dev/fd1') with a new parameter set with the name entry found in `/etc/mediaprm' (usually named 360/360, etc.). For autodetecting floppy devices, these parameters stay in effect until the media is changed. For "fixed parameter" devices, they stay in effect until they are changed again. Setfdprm can also be used by the superuser to redefine the default formats. Options -p device name Permanently loads a new parameter set for the specified auto-configuring floppy device for the configuration with name in `/etc/mediaprm'. Alternatively, the parameters can be given directly from the command line. -c device Clears the parameter set of the specified auto-configuring floppy device. -y device Enables format detection messages for the specified auto-configuring floppy device. -n device Disables format detection messages for the specified auto-configuring floppy device. Media description Please see the Media description section in the full fdutils documentation: - Texinfo documentation (info fdutils) - HTML documentation in /usr/share/doc/fdutils/Fdutils.html - or DVI documentation in /usr/share/doc/fdutils/Fdutils.dvi.gz Bugs This documentation is grossly incomplete. See Also Fdutils' texinfo doc fdutils-5.5 03Mar05 setfdprm(1)