Visit The New, Modern Unix Linux Community

Linux and UNIX Man Pages

Test Your Knowledge in Computers #652
Difficulty: Easy
Puffy is the mascot of Linux Mint.
True or False?
Linux & Unix Commands - Search Man Pages

irw(1) [debian man page]

IRW(1)								   User Commands							    IRW(1)

NAME
irw - sends data from Unix domain socket to stdout SYNOPSIS
irw [socket] DESCRIPTION
irw will connect to any Unix domain socket and will print the data that it receives to stdout. If you don't give it a socket name argument it will watch /var/run/lirc/lircd. Useful for debugging. -h --help display usage summary -v --version display version SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory. irw 0.9.0-pre1 October 2010 IRW(1)

Check Out this Related Man Page

IRSEND(1)								FSF								 IRSEND(1)

NAME
irsend - basic LIRC program to send infra-red commands SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...] DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such as TV boxes, HiFi sets, etc. DIRECTIVE can be: SEND_ONCE - send CODE [CODE ...] once SEND_START - start repeating CODE SEND_STOP - stop repeating CODE LIST - list configured remote items SET_TRANSMITTERS - set transmitters NUM [NUM ...] SIMULATE - simulate IR event REMOTE is the name of a remote, as described in the lircd configuration file. CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file. NUM is the transmitter number of the hardware device. For the LIST DIRECTIVE, REMOTE and/or CODE can be empty: LIST "" "" - list all configured remote names LIST REMOTE "" - list all codes of REMOTE LIST REMOTE CODE - list only CODE of REMOTE The SIMULATE command only works if it has been explicitly enabled in lircd. -h --help display usage summary -v --version display version -d --device use given lircd socket [/var/run/lirc/lircd] -a --address=host[:port] connect to lircd at this address -# --count=n send command n times EXAMPLES
irsend LIST DenonTuner "" irsend SEND_ONCE DenonTuner PROG-SCAN irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3 irsend SEND_STOP OnkyoAmpli VOL-DOWN irsend SET_TRANSMITTERS 1 irsend SET_TRANSMITTERS 1 3 4 irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S" FILES
/etc/lirc/lircd.conf Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave- form details. DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics: "irsend: could not connect to socket" "irsend: Connection refused" (or "Permission denied"). SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory. lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org. irsend 0.8.7pre1 May 2010 IRSEND(1)

6 More Discussions You Might Find Interesting

1. Filesystems, Disks and Memory

Quantum Firware Flash

Tried to use some 18gb Quantum Atlas III's (TD18J011) in my RS/6000's but resulted in horribly slow bootup times. These were Auspex pulls. Anyone know availability of firmware updates for these? No luck searching so far. Not sure if this would help with original problem, but worth the shot.... (0 Replies)
Discussion started by: mooshkie
0 Replies

2. AIX

P-Series (7029-6C3) firware recovery?

I have a 7029-6C3 that was running AIX 5.2; I tried to update to 5.2.10.5, rebooted, and the box went south. Upon further digging through the h/w logs, I found the error "Service Processor Firmware Failure" I can't get the machine to boot - not even to CD. How can I recover from this? Or can... (10 Replies)
Discussion started by: thomn8r
10 Replies

3. What is on Your Mind?

radio/airwaves *nix?

hey there, new to the forums here. long story short, i have interests in both HAM radio and *nix OS's and want to start a project that will combine the two. so, the question is: are there any *nix flavors or other distros that were specifically designed for radio/airwave communications, or... (0 Replies)
Discussion started by: BartlettMagic
0 Replies

4. Shell Programming and Scripting

how to calculate all pairwise distances in two dimensions and transform them into a matrix

Hello to all, I am very new in the shell scripting and I need help. I have data for several individuals in several rows followed by a tag and by 5 values per row, with the name of the individual in the first column, e.g.: IND1 H1 12 13 12 15 14 IND2 H2 12 12 15 14 14 IND3 H1 12 15... (2 Replies)
Discussion started by: Bemar
2 Replies

5. Shell Programming and Scripting

Split files by pairwise combination

I have 2 files $ cat tmp A1 File1a B1 File1b A2 File2a B2 File2b A1 File1a B3 File3b and $ cat tmp1 A1/B1 File3 A1/B1 File4 A1/B1 File5 A1/B1 File6 A1/B1 File7 A2/B2 File8 A2/B2 File9 A2/B2 File10 (1 Reply)
Discussion started by: senhia83
1 Replies

6. UNIX for Beginners Questions & Answers

Create 'n' number random pairwise combination of words

File 1 contains the list of words that needed to be randomly paired: Tiger Cat Fish Frog Dog Mouse Elephant Monkey File 2 contains the pairs that should not be used (in any solution) during random pairing. Elephant-Dog Cat-Fish Monkey-Frog Dog-Elephant, Fish-Cat, Frog-Monkey... (1 Reply)
Discussion started by: sammy777888
1 Replies

Featured Tech Videos