z8530_status_clear(9) [centos man page]

Z8530_STATUS_CLEAR(9)						Internal Functions					     Z8530_STATUS_CLEAR(9)

NAME

       z8530_status_clear - Handle status events from a stopped chip

SYNOPSIS

       void z8530_status_clear(struct z8530_channel * chan);

ARGUMENTS

       chan
	   Z8530 channel to shut up

DESCRIPTION

       Status interrupt vectors for a Z8530 that is in 'parked' mode. For machines with PCI Z85x30 cards, or level triggered interrupts (eg the
       MacII) we must clear the interrupt cause or die.

AUTHOR

       Alan Cox <alan@lxorguk.ukuu.org.uk>
	   Author.

COPYRIGHT

Kernel Hackers Manual 3.10					     June 2014						     Z8530_STATUS_CLEAR(9)

TCIC(4) 						     Kernel Interfaces Manual							   TCIC(4)

NAME

       tcic - Databook TCIC-2 PCMCIA controller driver

SYNOPSIS

       insmod	tcic.o	 [pc_debug=n]	[tcic_base=n]  [ignore=n]  [do_scan=n]	[irq_list=i,j,...]   [cs_irq=n]  [poll_interval=n]  [poll_quick=n]
       [cycle_time=n]

DESCRIPTION

       This is the low-level driver for the Databook TCIC-2 PCMCIA host controller family.  It is used by Card Services for programming the TCIC-2
       chip, and for monitoring card status change events.

PARAMETERS

       pc_debug=n
	      Selects  the PCMCIA debugging level.  This parameter is only available if the module is compiled with debugging enabled.	A non-zero
	      value enables debugging.

       tcic_base=n
	      Sets the base I/O port address of the TCIC-2 chip.  The default is 0x240.

       ignore=n
	      Causes the driver to ignore a single socket.  Sockets are numbered starting at 0.  The socket will be left in whatever state it  was
	      already in, so it can be used for cards with point enablers that do not cooperate with Card Services.

       do_scan=n
	      This flag specifies that all free interrupts should be tested to see if they can be triggered by the PCMCIA controller.  The default
	      is 1 (on).

       irq_list=i,j,...
	      Specifies the set of interrupts that may be allocated by this driver, if they are otherwise available.  The default list is 3, 4, 5,
	      6, 7, 10, 11, and 14.

       cs_irq=n
	      Sets  the  interrupt  line  to  use  for monitoring card status changes.	The default is 0, which means pick any legal interrupt not
	      already in use.  Legal values are 14, 10, 7, 6, 5, 4, and 3.

       poll_interval=n
	      Sets the card status polling delay, in 1/100 second increments.  If this parameter is set, card status interrupts will be disabled.

       poll_quick=n
	      When a card status change interrupt is received, the TCIC-2 chip is briefly polled for additional status	changes.   This  parameter
	      sets the polling delay, in 1/100 second increments.  The default is 5, meaning 0.05 seconds.

       cycle_time=n
	      Sets  the length of a CCLK external clock cycle, in nanoseconds.	The default is 70 ns, corresponding to a standard ISA 14.31818 MHz
	      clock.

AUTHOR

       David Hinds - dahinds@users.sourceforge.net

SEE ALSO

       cardmgr(8), pcmcia(5).

pcmcia-cs							2000/06/12 21:24:48							   TCIC(4)