iscsi_create_session(9) [centos man page]

ISCSI_CREATE_SESSION(9) 					  SCSI mid layer					   ISCSI_CREATE_SESSION(9)

NAME

       iscsi_create_session - create iscsi class session

SYNOPSIS

       struct iscsi_cls_session * iscsi_create_session(struct Scsi_Host * shost, struct iscsi_transport * transport, int dd_size,
						       unsigned int target_id);

ARGUMENTS

       shost
	   scsi host

       transport
	   iscsi transport

       dd_size
	   private driver data size

       target_id
	   which target

DESCRIPTION

       This can be called from a LLD or iscsi_transport.

AUTHORS

       James Bottomley <James.Bottomley@hansenpartnership.com>
	   Author.

       Rob Landley <rob@landley.net>
	   Author.

COPYRIGHT

Kernel Hackers Manual 3.10					     June 2014						   ISCSI_CREATE_SESSION(9)

FC_REMOTE_PORT_DELET(9) 					  SCSI mid layer					   FC_REMOTE_PORT_DELET(9)

NAME

       fc_remote_port_delete - notifies the fc transport that a remote port is no longer in existence.

SYNOPSIS

       void fc_remote_port_delete(struct fc_rport * rport);

ARGUMENTS

       rport
	   The remote port that no longer exists

DESCRIPTION

       The LLDD calls this routine to notify the transport that a remote port is no longer part of the topology. Note: Although a port may no
       longer be part of the topology, it may persist in the remote ports displayed by the fc_host. We do this under 2 conditions: 1) If the port
       was a scsi target, we delay its deletion by "blocking" it. This allows the port to temporarily disappear, then reappear without disrupting
       the SCSI device tree attached to it. During the "blocked" period the port will still exist. 2) If the port was a scsi target and disappears
       for longer than we expect, we'll delete the port and the tear down the SCSI device tree attached to it. However, we want to semi-persist
       the target id assigned to that port if it eventually does exist. The port structure will remain (although with minimal information) so that
       the target id bindings remails.

       If the remote port is not an FCP Target, it will be fully torn down and deallocated, including the fc_remote_port class device.

       If the remote port is an FCP Target, the port will be placed in a temporary blocked state. From the LLDD's perspective, the rport no longer
       exists. From the SCSI midlayer's perspective, the SCSI target exists, but all sdevs on it are blocked from further I/O. The following is
       then expected.

       If the remote port does not return (signaled by a LLDD call to fc_remote_port_add) within the dev_loss_tmo timeout, then the scsi target is
       removed - killing all outstanding i/o and removing the scsi devices attached ot it. The port structure will be marked Not Present and be
       partially cleared, leaving only enough information to recognize the remote port relative to the scsi target id binding if it later appears.
       The port will remain as long as there is a valid binding (e.g. until the user changes the binding type or unloads the scsi host with the
       binding).

       If the remote port returns within the dev_loss_tmo value (and matches according to the target id binding type), the port structure will be
       reused. If it is no longer a SCSI target, the target will be torn down. If it continues to be a SCSI target, then the target will be
       unblocked (allowing i/o to be resumed), and a scan will be activated to ensure that all luns are detected.

       Called from normal process context only - cannot be called from interrupt.

NOTES

       This routine assumes no locks are held on entry.

AUTHORS

       James Bottomley <James.Bottomley@hansenpartnership.com>
	   Author.

       Rob Landley <rob@landley.net>
	   Author.

COPYRIGHT

Kernel Hackers Manual 3.10					     June 2014						   FC_REMOTE_PORT_DELET(9)