Is possible to bridge wlan0 and eth0 using network manager?How to for wpa?


 
Thread Tools Search this Thread
Operating Systems Linux Is possible to bridge wlan0 and eth0 using network manager?How to for wpa?
# 1  
Old 04-16-2018
Is possible to bridge wlan0 and eth0 using network manager?How to for wpa?

I have created a bridge with nmcli between eth0 and wlan0

I use this procedure

Code:
sudo nmcli con add ifname br0 type bridge con-name br0
sudo nmcli con add type bridge-slave ifname eth0 master br0
sudo nmcli con add type bridge-slave ifname wlan0 master br0
sudo nmcli con modify br0 bridge.stp no
sudo nmcli con down eth0
sudo nmcli con down wlan0
sudo nmcli up br0

The bridge works,i can ping is ipv4 address..but..how to do for wpa2?
I prefer to use nmcli.
# 2  
Old 05-16-2018
Solution found: the bridge is created,but doesn't work.
Instead of bridge wlan and eth I create a network virtual wich point to wlan0 with virt-manager.
Works fine
Login or Register to Ask a Question

Previous Thread | Next Thread

8 More Discussions You Might Find Interesting

1. Red Hat

Network bandwidth Manager

Dear Engineer, Can anyone please inform me some application name like (CBQ) to control network bandwidth and please provide me the url to configure it. With Best Regards, Md. Abdullah-Al Kauser (1 Reply)
Discussion started by: makauser
1 Replies

2. Linux

Network bandwidth Manager

Dear Engineer, Can anyone please inform me some application name like (CBQ) to control network bandwidth and please provide me the url to configure it. With Best Regards, Md. Abdullah-Al Kauser (0 Replies)
Discussion started by: makauser
0 Replies

3. Red Hat

Unable To Activate Ethernet Network Device in RHEL 5.5 - e100 device eth0 does not seem to be presen

Hi All, Could anyone please help to resolve the below problem. I installed RHEL5.5 in my desktop.But when i try to activate the ethernet connection then it gives me the error. I spent 2 days for the above and go through with several suggestion found by googling. But no luck. ... (0 Replies)
Discussion started by: Tanmoy
0 Replies

4. UNIX for Dummies Questions & Answers

smc2582w-b bridge and solaris 10 wireless network

Hellow, I have a smc2582w-b brigde/acces point whom i configured on my windows vista pc and it works i have wireless acces to my network. Then i plugged it in to my 420r enterprise and it doesn't give any link activity on the lan piece of my server and my bridge/AP when i plug the cable... (3 Replies)
Discussion started by: chelle007
3 Replies

5. Red Hat

[tip] network route-eth0

hi, i would like to share this /etc/sysconfig/network-script/route-eth0 GATEWAY0=XXXXXX NETMASK0=XXXXXX ADDRESS0=XXXXXXX a delete route command with "route del -net xxxx...." will work but if the above exist and you reboot the linux then old route will be invoke on that config-route. ... (0 Replies)
Discussion started by: itik
0 Replies

6. Shell Programming and Scripting

Need help: Script to edit the hosts, network and eth0 file

Hello all :) I am new to scripting. I need somebody to help me write a script that can edit the files. For eg: if i say ./script <ipadd> <hostname> then it should change the ipaddress and hostname in the following files: 1. /etc/hosts 2. /etc/sysconfig/network 3.... (1 Reply)
Discussion started by: Shaikjaveed
1 Replies

7. Windows & DOS: Issues & Discussions

WPA crash vista???

Okay. I need help since I barely use M$ any more, the last time I used it for something other than school, work, or AIM was back in the days of WIN98. I was just reading the article on this site, Is Microsoft about to release a Windows “kill switch”? | Ed Bott's Microsoft Report | ZDNet.com, and... (0 Replies)
Discussion started by: Texasone
0 Replies

8. AIX

AIX and HP Network Node Manager

We are using hp's network node manager and would like to monitor quite a few of our aix boxes. It appears that nnm does not have AIX mibs by default. Does anyone know where i can find mibs for aix to load into nnm? Thanks (0 Replies)
Discussion started by: zuessh
0 Replies
Login or Register to Ask a Question