If i don't have raid disks can i shut down dmraid device-mapper?

10 More Discussions You Might Find Interesting

1. Ubuntu

Md0 raid don't see my folders

I suddenly don't see my folders into /mnt/md0. What can be reason? mdadm --detail /dev/md* /dev/md0: Version : 1.2 Creation Time : Fri Jan 18 09:54:27 2019 Raid Level : raid1 Array Size : 1953383488 (1862.89 GiB 2000.26 GB) Used Dev Size : 1953383488 (1862.89 GiB...

2. UNIX for Advanced & Expert Users

Command to see the logical volume path, device mapper path and its corresponding dm device path

Currently I am using this laborious command lvdisplay | awk '/LV Path/ {p=$3} /LV Name/ {n=$3} /VG Name/ {v=$3} /Block device/ {d=$3; sub(".*:", "/dev/dm-", d); printf "%s\t%s\t%s\n", p, "/dev/mapper/"v"-"n, d}' Would like to know if there is any shorter method to get this mapping of...

3. Solaris

Hardware RAID using three disks

Dear All , Pl find the below command , # raidctl -l Controller: 1 Volume:c1t0d0 Disk: 0.0.0 Disk: 0.1.0 Disk: 0.3.0 # raidctl -l c1t0d0 Volume Size Stripe Status Cache RAID Sub Size ...

4. Red Hat

Device-mapper behaviour booting on init=bin/bash

Good morning Recently we needed to change the password from a redhat 6.5 system that no one knew the root password. Starting the system with the init=/bin/bash method took us to the following scenario: system_vg active with only root_lv and tmpfs mounted. our entries at fstab are like...

5. AIX

SCSI PCI - X RAID Controller card RAID 5 AIX Disks disappeared

Hello, I have a scsi pci x raid controller card on which I had created a disk array of 3 disks when I type lspv ; I used to see 3 physical disks ( two local disks and one raid 5 disk ) suddenly the raid 5 disk array disappeared ; so the hardware engineer thought the problem was with SCSI...

6. Solaris

Solaris not recognizing RAID 5 disks

I've just installed Sol 10 Update 9 on a Sun 4140 server and have a RAID 1 configuration (2 136 Gb drives) for the OS and have created a RAID 5 array (6 136 GB) drives. When i log into the system I am unable to see the RAID 5 disks at all. I've tried using the devfsadm command but no luck and...

7. Red Hat

Device Mapper Notations and LVM

Hi, I had a doubt regarding device mapper notations and their corresponding LVM volumes. I have configured a volume group with two logical volumes in it as root and swap. The entries in the /etc/fstab file show the dm notations namely, /dev/mapper/VolGroup00-LogVol01...

8. Red Hat

device-mapper-multipath path [undef]

I have an HP blade with Qlogic HBA's connected to an EVA8000. I have downloaded the latest multipath.conf from HP's website. The drive presented to the server appears to be configured and working except the output of "multipath -l" shows for all paths. What is causing this output? mpath0...

9. Solaris

Move disks to different StorEdge, keeping RAID

Hi. I need to move a 5 disk RAID5 array from a SE3310 box to a different SE3310 array. After installing the disks in the "new" StorEdge device, I "would like" ;) to be able have access to the data which is on the RAID. Essentially, the quesion is, how can this be done? :confused: I checked...

10. Red Hat

IBM RAID disks

We have a Red Hat linux server running on IBM x445 hardware. There are external disks in an IBM EXP300 disk enclosure. The system is running RAID 5. One of the four IBM disks (73.4 GB 10k FRU 06P5760) has become faulty. The system is still up and running OK because of the RAID. In that same EXP300...

LEARN ABOUT SUSE

wipefs

WIPEFS(8)						       MAINTENANCE COMMANDS							 WIPEFS(8)

NAME

       wipefs - wipe a filesystem signature from a device

SYNOPSIS

       wipefs [-ahnp] [-o offset] device

DESCRIPTION

       wipefs allows to erase filesystem or raid signatures (magic strings) from the device to make the filesystem invisible for libblkid.  wipefs
       does not erase the whole filesystem or any other data from the device.  When used without options -a or -o, it lists all  visible  filesys-
       tems and offsets of their signatures.

OPTIONS

       -a, --all
	      Erase all available signatures.

       -h, --help
	      Print help and exit.

       -n, --no-act
	      Causes everything to be done except for the write() call.

       -o, --offset offset
	      Specifies  location (in bytes) of the signature which should be erased from the device. The offset number may include a "0x" prefix,
	      and then the number will be read as a hex value. It is possible to specify multiple -o options.

       -p, --parsable
	      Print out in parsable instead of printable format. Encode all potentially unsafe characters of a string  to  the	corresponding  hex
	      value prefixed by 'x'.

AUTHOR

       Karel Zak <kzak@redhat.com>.

AVAILABILITY

       The wipefs command is part of the util-linux-ng package and is available from ftp://ftp.kernel.org/pub/linux/utils/util-linux-ng/.

SEE ALSO

       blkid(8) findfs(8)

Linux								   October 2009 							 WIPEFS(8)

Linux