10 More Discussions You Might Find Interesting
1. UNIX for Beginners Questions & Answers
Hi,
Getting the below error while installing from ks.cfg unable to open input kickstart file curl#37 Couldn't open file /tmp/swappart
Here am trying to include /tmp/swappart file from pre section under disks and partition section. Dont know where exactly am doing wrong
My kickstart file... (3 Replies)
Discussion started by: Sumanthsv
3 Replies
2. Red Hat
HI Admin,
We are facing a weird issue with NTP. A physical server RHEL 5.11 is migrated as P2V. NTP was running & clocks are in sync on source server before migration.
After the SVMotion, On the target Linux guest, the ntpd is not able to sync with any of the clocks except local. Forcefully... (1 Reply)
Discussion started by: snchaudhari2
1 Replies
3. Fedora
Can anyone tell me how you create a kickstart file for RHEL 6.1 install? I am new to this and wanting to learn Red Hat. I have a training guide that says to create one but it does not give you instructions on how to do so. (3 Replies)
Discussion started by: Saplmb
3 Replies
4. Red Hat
I have Dell laptop having windows 8
vmware workstation 9
redhat 7.2
After installation it only get me into text mode instead f GUI
Please help (4 Replies)
Discussion started by: hananabbas
4 Replies
5. Red Hat
Hello,
I am setting up a new RedHat server with two network interfaces.
These interfaces are on different subnets, and connected to the same firewall.
I'm trying to reach a remote IP.
It works fine from the first interface.
The second interface however, is making ARP requests instead of... (0 Replies)
Discussion started by: Wanou85
0 Replies
6. Red Hat
Hi all
m newbie in linux and trying to setup my internal DNS server for local network.After messing with DNS for hours i am posting this.
i have configured /etc/resolve.conf, hostname with domain name in /etc/sysconfig/network file,/etc/hosts file with local host entry and zone file... (1 Reply)
Discussion started by: Vaibhav.T
1 Replies
7. Shell Programming and Scripting
Hi,
I would like to create a script so that it will ask me the following:
1) What is the ip address?
2) What is the gateway address?
3) What is the hostname?
and then put the answer to the below kickstart file (kickstart.cfg)
Here I included the kickstart.cfg:
# Kickstart file... (9 Replies)
Discussion started by: beeloo
9 Replies
8. UNIX for Advanced & Expert Users
Hi,
I was able to set up a kickstart to install Red Hat Enterprise thought a network.
I'm trying to enable a NTP time server in the post section of the kickstart file and also enable/disable a few services using chkconfig.
I can't seam to get it to work, can anyone help ? I don't beleive i... (2 Replies)
Discussion started by: Georgesaa
2 Replies
9. UNIX for Advanced & Expert Users
Hi,
I have few questions to make this kickstart file to be more efficient:
1) I would like to reboot the server once the installation (included installed all the optional rpm) is done.
2) Is there a nicer way to install rpm packages? (Here I included the commands in my kickstart file)
#... (1 Reply)
Discussion started by: beeloo
1 Replies
10. Linux
Would anyone know how to set a NIC to 100 Full Duplex from within a kickstart bootdisk? I just added the Tigon3 module to the bootnet.img - it loads fine but auto-negotiates to 100 Half Duplex for some reason - are there any parameters I can pass on the boot disk to force it 100 Full
appreciate... (2 Replies)
Discussion started by: silvaman
2 Replies