10 More Discussions You Might Find Interesting
1. Ubuntu
Hi
Please can you help me to understand what could be wrong based on what I have captured in the logs:
I have run cat /var/log/syslog | grep -i warn, and I got the following output NetworkManager: <warn> Activation (eth3) failed.
Dec 23 10:58:25 cmoveldb02 NetworkManager: <warn> (eth3): DHCPv4... (2 Replies)
Discussion started by: fretagi
2 Replies
2. Red Hat
Dear All ,
While taking backups in one Linux Server , we find one alert came with regard to Network Interface Card.
Pl find the below alert.
Network Interface Card performance for NIC:eth1 has exceeded Major threshold.
Bytes sent and received per second (Average)= 105540.303101... (6 Replies)
Discussion started by: jegaraman
6 Replies
3. Solaris
Hi All,
Can somebody explain that whats the meaning of different interfaces naming scheme, Like ' hme, qfe, e1000g0, ce, eri, bge' ?
This is such a basic question which i always overlooked :(
Thanks ! (6 Replies)
Discussion started by: Solarister
6 Replies
4. Solaris
Hi Experts,
Can we use some command from unix to find the available network interface? I did tried
Its listing following, however how can I decide the which vender card is attached
e.g. if its hme , bge or some thing else
Thanks (7 Replies)
Discussion started by: kumarmani
7 Replies
5. UNIX for Dummies Questions & Answers
I have three network cards in my unix box. I need to figure out which card corresponds to an assigned IP address. If there some command in unix I can use to make an ethernet interface blink?
Any advice would be appreciated. (6 Replies)
Discussion started by: mojoman
6 Replies
6. UNIX for Dummies Questions & Answers
Hi!.
I have problems installing my network card under
ther redhat kernel.
First i tryed my integrated intel pro set 10/100
then my d-link 530tx Pci but none of them seems to
be found.
also i huse my network card to connect to the net
trough PPPOE where i need to type my username and... (3 Replies)
Discussion started by: Gibbler
3 Replies
7. UNIX for Advanced & Expert Users
hi, everyone:
alpha 600 au true64 Unix 4.0f
my network cart is set "Auto-Negotiate".After operate system startup,the network will be disconnected by itself at sometime. I found some prompt in /usr/adm/messages.
"tu0 :transmit FIFO underflow:threshold raised to :256 byteŁ¬link up... (1 Reply)
Discussion started by: q30
1 Replies
8. UNIX for Advanced & Expert Users
I have been having trouble with my sis900 neytwork card in slacwkare linux. I tried to modprobe the sis900, it didnt give me any errors but it didnt load it. so I put in a realtek 8139 network card and tried it too. These are the errors i get with the two cards when trying to do insmod on either of... (3 Replies)
Discussion started by: The Fridgerator
3 Replies
9. UNIX for Dummies Questions & Answers
1) i am trying to install realtek network card in caldrea linux, but i am not able to find the interface,
2)i download drivers for network card and i am not able to read the floopy in linux, pls help me out. (1 Reply)
Discussion started by: gops
1 Replies
10. IP Networking
I have a UnixWare 2 server that has an ISA 3Com NIC that has just a BNC connector on it. I want to remove this and install an ISA 3Com NIC that has a BNC/RJ45 connector. What steps do I have to go through to successfully complete this? Thye are almost the exact same cards except for the... (1 Reply)
Discussion started by: cparks
1 Replies
named-xfer(8) System Manager's Manual named-xfer(8)
Name
named-xfer - pull BIND/Hesiod zones from another server
Syntax
/usr/etc/named-xfer -z zone_to_transfer -f db_file -s serial_no [ -d debug_level ] [ -l debug_log_file ] [ -t trace_file ] [ -p port ] [ -n
] [ -a auth_type.auth_ver ] servers...
Description
The transfer daemon, is a server that is usually run by the daemon, but it can also be run manually with the given arguments. The transfer
daemon runs on a BIND/Hesiod secondary server and pulls BIND/Hesiod zones from a primary server. This daemon is not run by default, nor
can it be started up from
Options
-z zone_to_transfer
This option is required to pull a zone. The zone_to_transfer argument specifies the name of the BIND/Hesiod zone that
the daemon will transfer, for example, dec.com.
-f db_file This option is required to pull a zone. The db_file argument specifies the name of the file into which the pulled zone
information is placed.
-s serial_no This option is required to pull a zone. The serial_no argument should be set to the current serial number of the SOA
record for the zone zone_to_transfer. If serial_no is set to 0, the zone is always pulled.
-d debug_level The debug_level argument sets the debug level and determines the amount of debug information to be displayed.
-l debug_log_file The debug_log_file argument specifies the file that will contain any debug messages from the zone pull.
-t trace_file The trace_file argument specifies the file that will contain a trace from the zone pull.
-p port The port argument specifies the port that will be used instead of the default nameserver port listed in
-n This option must be used when the daemon is running in the network safe mode. It indicates that the zone pull must be
authenticated.
-a auth_type.auth_ver
This option must be used if the daemon is running in the network safe mode. The auth_type argument indicates what type
of authentication to use and the auth_ver argument indicates what version of the authentication type to use. Currently,
the auth_type must be "kerberos" and the auth_ver must be "one".
servers... The servers argument is a list of Internet addresses from which to pull a zone. If the first host cannot be ddreached,
the transfer daemon will try to pull the zone from the next host listed.
See Also
services(5), named(8), kerberos(8krb)
Guide to the BIND/Hesiod Service
Guide to Kerberos
named-xfer(8)