10 More Discussions You Might Find Interesting
1. Ubuntu
Hi
Please can you help me to understand what could be wrong based on what I have captured in the logs:
I have run cat /var/log/syslog | grep -i warn, and I got the following output NetworkManager: <warn> Activation (eth3) failed.
Dec 23 10:58:25 cmoveldb02 NetworkManager: <warn> (eth3): DHCPv4... (2 Replies)
Discussion started by: fretagi
2 Replies
2. Red Hat
Dear All ,
While taking backups in one Linux Server , we find one alert came with regard to Network Interface Card.
Pl find the below alert.
Network Interface Card performance for NIC:eth1 has exceeded Major threshold.
Bytes sent and received per second (Average)= 105540.303101... (6 Replies)
Discussion started by: jegaraman
6 Replies
3. Solaris
Hi All,
Can somebody explain that whats the meaning of different interfaces naming scheme, Like ' hme, qfe, e1000g0, ce, eri, bge' ?
This is such a basic question which i always overlooked :(
Thanks ! (6 Replies)
Discussion started by: Solarister
6 Replies
4. Solaris
Hi Experts,
Can we use some command from unix to find the available network interface? I did tried
Its listing following, however how can I decide the which vender card is attached
e.g. if its hme , bge or some thing else
Thanks (7 Replies)
Discussion started by: kumarmani
7 Replies
5. UNIX for Dummies Questions & Answers
I have three network cards in my unix box. I need to figure out which card corresponds to an assigned IP address. If there some command in unix I can use to make an ethernet interface blink?
Any advice would be appreciated. (6 Replies)
Discussion started by: mojoman
6 Replies
6. UNIX for Dummies Questions & Answers
Hi!.
I have problems installing my network card under
ther redhat kernel.
First i tryed my integrated intel pro set 10/100
then my d-link 530tx Pci but none of them seems to
be found.
also i huse my network card to connect to the net
trough PPPOE where i need to type my username and... (3 Replies)
Discussion started by: Gibbler
3 Replies
7. UNIX for Advanced & Expert Users
hi, everyone:
alpha 600 au true64 Unix 4.0f
my network cart is set "Auto-Negotiate".After operate system startup,the network will be disconnected by itself at sometime. I found some prompt in /usr/adm/messages.
"tu0 :transmit FIFO underflow:threshold raised to :256 byteŁ¬link up... (1 Reply)
Discussion started by: q30
1 Replies
8. UNIX for Advanced & Expert Users
I have been having trouble with my sis900 neytwork card in slacwkare linux. I tried to modprobe the sis900, it didnt give me any errors but it didnt load it. so I put in a realtek 8139 network card and tried it too. These are the errors i get with the two cards when trying to do insmod on either of... (3 Replies)
Discussion started by: The Fridgerator
3 Replies
9. UNIX for Dummies Questions & Answers
1) i am trying to install realtek network card in caldrea linux, but i am not able to find the interface,
2)i download drivers for network card and i am not able to read the floopy in linux, pls help me out. (1 Reply)
Discussion started by: gops
1 Replies
10. IP Networking
I have a UnixWare 2 server that has an ISA 3Com NIC that has just a BNC connector on it. I want to remove this and install an ISA 3Com NIC that has a BNC/RJ45 connector. What steps do I have to go through to successfully complete this? Thye are almost the exact same cards except for the... (1 Reply)
Discussion started by: cparks
1 Replies
smd-loop(1) Sync Mail Dir (smd) documentation smd-loop(1)
NAME
smd-loop - iterates smd-pull and smd-push
SYNOPSIS
smd-loop [-vt]
DESCRIPTION
smd-loop runs smd-push and smd-pull at regular intervals as defined by the user in the ~/.smd/loop configuration file. On errors that are
reported to be transient, it retries a second time before failing.
The configuration file is line-oriented. Each line is composed of three space separated fields: pull-frequency, push-frequency and end-
point-name. Frequencies are expressed in minutes, while endpoint name is a valid name for smd-pull(1) and smd-push(1). Lines beginning with
# are considered as comments. The following example calls the command smd-pull default every 3 minutes, and smd-push default every 10.
Example:
# pull-frequency push-frequency endpoint-name
3 10 default
OPTIONS
-v Increase program verbosity (printed on stderr)
-t Just create a template configuration file if none
FILES
~/.smd/loop
SEE ALSO
mddiff(1), smd-server(1), smd-client(1), smd-push(1), smd-pull(1)
AUTHOR
Enrico Tassi <gares@fettunta.org>
11 June 2012 smd-loop(1)