10 More Discussions You Might Find Interesting
1. Solaris
Hi,
I have Solaris-10 server and link aggregation is configured on this in below way
# dladm show-aggr
key: 1 (0x0001) policy: L4 address: 3c:d9:2b:ee:a8:a (auto)
device address speed duplex link state
bnx1 3c:d9:2b:ee:a8:a... (8 Replies)
Discussion started by: solaris_1977
8 Replies
2. Solaris
Hi,
I'm not from the Solaris world and some of these things are new to me. Can someone tell me if it is possible to configure link aggregation without using LACP?
I am told etherchannel was setup without LACP. (3 Replies)
Discussion started by: techy1
3 Replies
3. HP-UX
Hi,
I want to Break the Link Aggregation. My aggregation are lan0+lan1 = lan900.
Now I want to break this and put the IP in lan0. But i have cluster environment and this is the main database server.
So It need to change in cluster script.
But I dont know where I have to change it.
Please... (1 Reply)
Discussion started by: mkiron
1 Replies
4. Solaris
Me again :)
I'm trying to find a page describing the L2, L3 und L4 modes of dladm.
It's nice to read "hashed by ip header", but how should I use that?
On the file-server it's ok to have the six interfaces serving six clients each on it's own. But an rsync connection via switch between two... (8 Replies)
Discussion started by: PatrickBaer
8 Replies
5. HP-UX
Hi,
Hoping someone can offer some advice on something i have not dealt with before.
We have a server that seems to have some very strange configuration done on it. It has 2 physical NIC's and rather than both be aggregated into LAN900 we have 1 in LAN900 and 1 in LAN901? (See Below)... (2 Replies)
Discussion started by: Andyp2704
2 Replies
6. AIX
Hi,
I need to setup a hacmp cluster (my first one, we usually use VCS on AIX), but I require more network bandwith than a normal gigabit etherchannel setup can provide, so I am thinking about using linkaggregation - 2 active adapters to one switch and a single backup adapter to another switch... (4 Replies)
Discussion started by: zxmaus
4 Replies
7. IP Networking
I have some linux machines that I am trying to increase the throughput to on a single connection. They connect to a switch with two 1GbE lines and the switch does not have Link Aggregation support for these machines. I have tried bonding with balance-rr, balance-alb, but the machines can only... (4 Replies)
Discussion started by: Eruditass
4 Replies
8. Solaris
Hi everybody,
One client asked me to configure network failover and load balancing for two Ethernet interfaces, I tried IPMP but I was unable to do so, because he's using his Gateway as firewall and PING is disabled.
so IPMP kept telling me that all interfaces failed because gateway can't be... (8 Replies)
Discussion started by: Sun Fire
8 Replies
9. UNIX for Advanced & Expert Users
Hi there
I have a requirement to provide failover to our customer boxes in case of interface / switch failure, I have been looking at Solaris Link Aggregation with LACP and I wanted to ask a question
Ive seen multiple websites that say the following
Does this also mean that if the... (1 Reply)
Discussion started by: hcclnoodles
1 Replies
10. Solaris
Hi there
I have a requirement to provide failover to our customer boxes in case of interface / switch failure, I have been looking at Solaris Link Aggregation with LACP and I wanted to ask a question
Ive seen multiple websites that say the following
Does this also mean that if the... (2 Replies)
Discussion started by: hcclnoodles
2 Replies
ARNO-IPTABLES-FIREWALL(8) ARNO-IPTABLES-FIREWALL(8)
NAME
arno-iptables-firewall - Single- & multi-homed firewall script with DSL/ADSL support.
SYNOPSIS
/etc/init.d/arno-iptables-firewall [start|stop|status|force-reload|restart]
DESCRIPTION
arno-iptables-firewall is an iptables configuration script with support for both IPv4 & IPv6. While it is extremely easy to use one can
nevertheless use it in quite complicated environments.
All available options are explained in the extensively documented configuration file.
The external interface of the system needs to be set up properly in the firewalls configuration file (EXT_IF). The default behavior of the
firewall is to deny all incoming connections.
For additional requirements not covered by the configuration file custom iptables rules can be placed in /etc/arno-iptables-firewall/cus-
tom-rules. This file is automatically parsed by the service script.
See the README file (eg. in /usr/(local/)share/doc/arno-iptables-firewall) for an example how to manage logging of firewall events through
syslogd.
The arno-fwfilter script can be used to make the firewall logs more readable for humans (see manpage).
Several plugins for the firewall script are available online. Plugins can be downloaded from http://rocky.eld.leidenuniv.nl/ Please see the
README file for more information.
FILES
/etc/init.d/arno-iptables-firewall system service script
/etc/arno-iptables-firewall/firewall.conf firewall configuration
/etc/arno-iptables-firewall/conf.d/ firewall configuration directory
/etc/arno-iptables-firewall/custom-rules custom iptables rules
/etc/arno-iptables-firewall/blocked-hosts host blacklist
/etc/arno-iptables-firewall/mac-addresses mac filter list
Please note, that the last two files do exist in the initial configuration and their use is disabled in /etc/arno-iptables-firewall/fire-
wall.conf
SEE ALSO
iptables(8), arno-fwfilter(1), syslog.conf(5)
The http://rocky.eld.leidenuniv.nl/ web site.
AUTHOR
arno-iptables-firewall was written by Arno van Amersfoort <arnova@rocky.eld.leidenuniv.nl>.
This manual page was written by Michael Hanke <michael.hanke@gmail.com>, for the Debian project (but may be used by others).
Michael Hanke March 14, 2012 ARNO-IPTABLES-FIREWALL(8)