10 More Discussions You Might Find Interesting
1. Solaris
Hi,
I have Solaris-10 server and link aggregation is configured on this in below way
# dladm show-aggr
key: 1 (0x0001) policy: L4 address: 3c:d9:2b:ee:a8:a (auto)
device address speed duplex link state
bnx1 3c:d9:2b:ee:a8:a... (8 Replies)
Discussion started by: solaris_1977
8 Replies
2. Solaris
Hi,
I'm not from the Solaris world and some of these things are new to me. Can someone tell me if it is possible to configure link aggregation without using LACP?
I am told etherchannel was setup without LACP. (3 Replies)
Discussion started by: techy1
3 Replies
3. HP-UX
Hi,
I want to Break the Link Aggregation. My aggregation are lan0+lan1 = lan900.
Now I want to break this and put the IP in lan0. But i have cluster environment and this is the main database server.
So It need to change in cluster script.
But I dont know where I have to change it.
Please... (1 Reply)
Discussion started by: mkiron
1 Replies
4. Solaris
Me again :)
I'm trying to find a page describing the L2, L3 und L4 modes of dladm.
It's nice to read "hashed by ip header", but how should I use that?
On the file-server it's ok to have the six interfaces serving six clients each on it's own. But an rsync connection via switch between two... (8 Replies)
Discussion started by: PatrickBaer
8 Replies
5. HP-UX
Hi,
Hoping someone can offer some advice on something i have not dealt with before.
We have a server that seems to have some very strange configuration done on it. It has 2 physical NIC's and rather than both be aggregated into LAN900 we have 1 in LAN900 and 1 in LAN901? (See Below)... (2 Replies)
Discussion started by: Andyp2704
2 Replies
6. AIX
Hi,
I need to setup a hacmp cluster (my first one, we usually use VCS on AIX), but I require more network bandwith than a normal gigabit etherchannel setup can provide, so I am thinking about using linkaggregation - 2 active adapters to one switch and a single backup adapter to another switch... (4 Replies)
Discussion started by: zxmaus
4 Replies
7. IP Networking
I have some linux machines that I am trying to increase the throughput to on a single connection. They connect to a switch with two 1GbE lines and the switch does not have Link Aggregation support for these machines. I have tried bonding with balance-rr, balance-alb, but the machines can only... (4 Replies)
Discussion started by: Eruditass
4 Replies
8. Solaris
Hi everybody,
One client asked me to configure network failover and load balancing for two Ethernet interfaces, I tried IPMP but I was unable to do so, because he's using his Gateway as firewall and PING is disabled.
so IPMP kept telling me that all interfaces failed because gateway can't be... (8 Replies)
Discussion started by: Sun Fire
8 Replies
9. UNIX for Advanced & Expert Users
Hi there
I have a requirement to provide failover to our customer boxes in case of interface / switch failure, I have been looking at Solaris Link Aggregation with LACP and I wanted to ask a question
Ive seen multiple websites that say the following
Does this also mean that if the... (1 Reply)
Discussion started by: hcclnoodles
1 Replies
10. Solaris
Hi there
I have a requirement to provide failover to our customer boxes in case of interface / switch failure, I have been looking at Solaris Link Aggregation with LACP and I wanted to ask a question
Ive seen multiple websites that say the following
Does this also mean that if the... (2 Replies)
Discussion started by: hcclnoodles
2 Replies
ipkungfu(8) System Manager's Manual ipkungfu(8)
NAME
ipkungfu - An iptables-based firewall for Linux
SYNOPSIS
ipkungfu [ -c ] [ -t ] [ -d ] [ -h ] [ -v ] [ --quiet ] [ --panic ] [ --no-caching
DESCRIPTION
ipkungfu is an iptables-based Linux firewall. The primary design goals are security, ease of use, and performance, in that order. It takes
advantage of advanced features of iptables, tcpwrappers, and the Linux kernel. It also simplifies the configuration of internet connection
sharing, advanced routing, and other networking needs.
OPTIONS
-c (or --check)
Check whether ipkungfu is loaded, and report any command line options it may have been loaded with.
-t (or --test)
Runs a configuration test, and displays the results. Note that this does not test or display all configuration options. This
gives you an opportunity to verify that major configuration options are correct before putting them into action.
-d (or --disable)
Disables the firewall. It is important to know exactly what this option does. All traffic is allowed in and out, and in the
case of a gateway, all NATed traffic is forwarded (the option retains your connection sharing options). Custom rules are not
implemented, and deny_hosts.conf is ignored.
-f (or --flush)
Disables the firewall COMPLETELY. All rules are flushed, all chains are removed. Any port forwarding or internet connection
sharing will cease to work.
-h (or --help)
Displays brief usage information and exits.
-v (or --version)
Displays version information and exits.
--quiet Runs ipkungfu with no standard output
--panic Drops ALL traffic in all directions on all network interfaces. You should probably never use this option. The --panic option
is available for the highly unusual situation where you know that an attack is underway but you know of no other way to stop
it.
--failsafe If ipkungfu fails, --failsafe will cause all firewall policies to revert to ACCEPT. This is useful when working with ipkungfu
remotely, to prevent loss of remote access due to firewall failure.
--no-caching
Disables rules caching feature.
FILES
/etc/ipkungfu/ipkungfu.conf
/etc/ipkungfu/advanced.conf
/etc/ipkungfu/accept_hosts.conf
/etc/ipkungfu/deny_hosts.conf
/etc/ipkungfu/custom.conf
/etc/ipkungfu/log.conf
/etc/ipkungfu/redirect.conf
/etc/ipkungfu/services.conf
/usr/sbin/ipkungfu
/usr/share/doc/ipkungfu/AUTHORS
/usr/share/doc/ipkungfu/README
/usr/share/doc/ipkungfu/FAQ
/usr/share/doc/ipkungfu/ChangeLog
/usr/share/doc/ipkungfu/COPYING
SEE ALSO
iptables(8).
January 2003 ipkungfu(8)