10 More Discussions You Might Find Interesting
1. UNIX for Beginners Questions & Answers
Dear friends
I use RedHat 6.5, which sets the gateway in the configuration file / etc / sysconfig / network as GATEWAY = 192.168.1.26, and the gateway in the configuration file / etc / sysconfig / network-scripts / ifcfg-eth11 as GATEWAY = 192.168.1.256. The two gateways are different.... (6 Replies)
Discussion started by: tanpeng
6 Replies
2. IP Networking
Dear gurus of Linux / Unix.
I have a server, which I use to monitoring traffic, the problem that I find is when I run the following command:
probe:~ # sar -n DEV 1
I see that I one second appear info in some interface and in the other second no appear, I don't know what will be the... (0 Replies)
Discussion started by: andresguillen
0 Replies
3. AIX
Hi .. we have two AIX 5.3 systems with a small client server app communicating over a TCP socket.
Box A has a single network interface where the server app (in Java) opens a well known port and waits for connections from Box B.
Box B has two network interfaces, X and Y. Interface X has the... (4 Replies)
Discussion started by: RonBowater
4 Replies
4. Solaris
Hi,
I have two physical interfaces on a servers.
We have connected them to differerent subnets.
1) First interface:
10.158.49.87 to newtwork 10.158.49.0, its gateway is 10.158.49.1
(It is added as default gateway)
It is existing set up. It works well
2) Second interface:
... (1 Reply)
Discussion started by: sri243
1 Replies
5. IP Networking
Hi gurus of unix, I haved installed my openSolaris in a HP530,
Recently I use the following command
beadm destry opensolaris1
beadm destry opensolaris2
After That I reboot my Laptop.
Well when I go to my work I try to open my wireshark tool, but the option in GUI interface does not appear!!!... (2 Replies)
Discussion started by: andresguillen
2 Replies
6. Debian
Hello
i am configuring a debian lenny sever ,/etc/network/interfaces is modified so that eth1 takes a static IP address
then i save it wq!
then i restart the networking , /etc/init.d/networking restart .
but after reboot ,the file is reset ,note that the interfaces had by defauklt IPv6 address... (5 Replies)
Discussion started by: learn82
5 Replies
7. Linux
Dear Sir
I am a newbie in the world of IP telephony. I have been working with Asterisk PBX (SIP) and Cisco Call Manager (MGCP) but now I am learning on how to work GNUGK for H.323 Gatekeeper.
I am having a problem, configuring static call routing on GNUGK
in the section
... (0 Replies)
Discussion started by: mfondoum
0 Replies
8. Linux
My setup consists of a hardware node, which hosts several virtual machines (OpenVZ, to be precise). The hardware node has two network interfaces (<ifA>, <ifB>) connected to different subnets (<networkA>, <networkB>). I want to route the traffic of certain VEs over <ifB> while routing the other VEs... (0 Replies)
Discussion started by: bakunin
0 Replies
9. SCO
Hi,
I have problems with my SCO unix network interfaces.
Intel integrated adapter was failing, so I installed new one - 3COM adapter into free PCI slot.
Installed driver using SCO Software manager - successfully
Added new Network adapter using SCO Network configuration manager - successfully... (0 Replies)
Discussion started by: vilius
0 Replies
10. IP Networking
Hi,
I have problems with my SCO unix network interfaces.
Intel integrated adapter was failing, so I installed new one - 3COM adapter into free PCI slot.
Installed driver using SCO Software manager - successfully
Added new Network adapter using SCO Network configuration manager - successfully... (0 Replies)
Discussion started by: vilius
0 Replies
ports(7) Miscellaneous Information Manual ports(7)
NAME
ports, port_names - Device (tty and lp) names for serial and parallel ports
SYNOPSIS
Default Serial Ports:
/dev/tty00
/dev/tty01 (not present on a single-port system)
Parallel Port:
/dev/lp0
DESCRIPTION
AlphaStation and AlphaServer systems provide one or two 9-pin serial communication ports. These ports are usually labelled 1 (COMM1) and 2
(COMM2), but they may be identified by different icons. Using the appropriate serial cable and terminator, you can connect a serial
printer, external modem, or character-cell terminal to a serial port. Most AlphaStation and AlphaServer systems also provide one parallel
port, for use with a parallel printer.
When you add a device to your system, the installation documentation may instruct you to map the device pathname to the port. These
devices are located in the /dev directory.
For serial-line ports, the two default device pathnames are: This pathname always maps to 1, COMM1, the lowest port number, an icon for a
terminal console, or the only serial port (on a single-port system). This pathname always maps to 2, COMM2, the next numbered port, or (if
one serial port is labeled with an icon for a terminal console) the remaining serial port.
If your system hardware has been extended to include additional serial ports, the pathnames /dev/tty02, /dev/tty03, and so forth, may also
be available to you. However, most systems have only /dev/tty00 and /dev/tty01 as the device pathnames for serial ports.
The one parallel port on an AlphaStation or AlphaServer may be labeled with the word printer or a printer icon. On some systems, the paral-
lel port may not be labeled. The device pathname for the parallel port is /dev/lp0. Currently, Tru64 UNIX does not fully support parallel
printers, so fewer devices are connected to this port as compared to serial ports.
If you are connecting a terminal console to your system, it must be connected to the serial port mapped to /dev/tty00. For other serial
devices, it does not matter which of the serial ports you choose for the connection. For example, suppose you are setting up a system that
has two serial ports, labeled 1 and 2. You intend to use a serial-line terminal rather than a workstation monitor as the system console and
also want to connect a serial-line printer to the system. In this case, you must connect the terminal to the port labeled 1 (with the
device pathname /dev/tty00). Therefore, you must connect the printer to the remaining port labeled 2 (with the device pathname /dev/tty01).
If, for the same type of system, you intend to use a workstation monitor as the system console, it does not matter which serial port you
use for a serial-line printer or modem. In other words, you can connect the printer to either port 1 (with pathname /dev/tty00) or port 2
(with pathname /dev/tty01). When prompted to enter a /dev/tty** pathname by the lprsetup script or the Print configuration tool in the CDE
Application Manager, you would specify /dev/tty00 if you connected the printer to port 1 or /dev/tty01 if you connected the printer to port
2.
See the System Administration manual for more information on setting up consoles (including remote consoles) and printers. See the
modem(7) reference page for more information on setting up modems.
SEE ALSO
Commands: lprsetup(8)
Devices: ace(7), modem(7)
System Administration delim off
ports(7)