9 More Discussions You Might Find Interesting
1. AIX
Hi Everyone,
Is it possible to configure bonding over bonded interface in AIX?
For example:
server has for NIC port:
ent0
ent1
ent2
ent3
First I create a EtherChannel ent4 from ent0 and ent1.
and then I create a EtherChannel ent5 from ent2 and ent3.
Can I create a EtherChannel... (1 Reply)
Discussion started by: nnnnnnine
1 Replies
2. AIX
Hello,
Please suggest me the ways how to get graphical interface on AIX server.I need to create oracle database for which I need graphical access.
Best regards,
Vishal (4 Replies)
Discussion started by: Vishal_dba
4 Replies
3. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
4. SCO
Hi all
I have installed a demo version of SCO OpenServer 5.0.2, I finally found it is Desktop Interface, I would like to know how to change its interface to dos based interface?
If you have any ideas, please tell me then. Thank you (2 Replies)
Discussion started by: TinhNhi
2 Replies
5. Solaris
Dear all,
I am a newbie in solaris and I need your advice.
I have a Solaris version 5.9 installed on Sunfire V240.
I am able to ssh the machine from putty remotely.
My problem is that I cannot see the display from KVM switch I have connected to it. I need also to be able to see the GUI... (2 Replies)
Discussion started by: mbouster
2 Replies
6. AIX
Hi All,
Please let me know the command to restart the network interface and enable it on boot in AIX, similar to /etc/init.d/network restart in Redhat.
Thanks,
Sunil.K
please watch out to post in the right subforum! (9 Replies)
Discussion started by: sunilrk07
9 Replies
7. AIX
Hi,
I am totally new to AIX. I would like to know how to create virtual interface on AIX machine.
Thanks,
Pooja (4 Replies)
Discussion started by: pooja84k
4 Replies
8. AIX
Hi,
I am trying to list all the interface present in the given system.
Here is sample program.
i.e. cat 1.c
#include <sys/types.h>
#include <sys/socket.h>
#include <sys/ioctl.h>
#include <sys/dlpi.h>
#include <net/if.h>
/*#include <sys/sockio.h>*/
#include <unistd.h>
#include... (3 Replies)
Discussion started by: jgobbur
3 Replies
9. AIX
Hello,
Under Linux (Cups) you can place an interface driver in:
/etc/cups/interfaces
.. which allows you to intercept printouts to a certain printer and then carry on with the printer.
Is there a similar function under AIX?
Thanks, (0 Replies)
Discussion started by: stuaz
0 Replies
IFSYSCTL(5) Network configuration IFSYSCTL(5)
NAME
ifsysctl[-<interface name>] - per network interface sysctl settings
SYNOPSIS
/etc/sysconfig/network/ifsysctl
/etc/sysconfig/network/ifsysctl-<interface name>
DESCRIPTION
These files are intended to contain sysctl settings, that should be applied when a network interface is created. This are usually interface
specific settings, like:
net.ipv6.conf.eth0.use_tempaddr = 1
or
net.ipv4.conf.eth0.rp_filter = 0
The settings are applied by the /etc/sysconfig/network/scripts/ifup-sysctl script executed via /etc/udev/rules.d/77-network.rules rule (see
udev(7)), after the creation and after the rename of the interface name to its persistent name (when applicable), but before the ifup
<interface name> -o hotplug may be executed to configure the interface.
The settings are not applied by default when the NetworkManager is active (NETWORKMANAGER=yes), except when the IFSYSCTL_NETWORKMANAGER=yes
variable is set in the /etc/sysconfig/network/config file.
Settings from the ifsysctl- file are applied every time an interface has been created.
Settings from the ifsysctl-interface name file are applied when the interface with the corresponding interface name has been created.
SYNTAX
The sysctl(8) utility is required to apply the settings. It supports two separator characters for sysctl keywords: a "." in default format
and a "/" in the alternate format. Therefore the syntax is basically same to the /etc/sysctl.conf file.
Interface names may contain a ".". In the default sysctl format using a "." as separator, that is any "." in the interface name of the key-
word, has to be replaced with a "/". In the alternate sysctl format with "/" as separator, normal interface names can be used.
Optionally, the ifsysctl files may contain also the $INTERFACE and the $SYSCTL_IF variables, that are automatically replaced with the cur-
rent interface name usable in the alternate format and with the sysctl-quoted interface name for the default format, before the settings
are passed to the sysctl utility.
Note also, that settings with variables in the ifsysctl (without the -<interface name> suffix), will be applied for every interface!
Further, files with variables are not compatible to the /etc/sysctl.conf file.
EXAMPLES
Settings for "eth0" and "eth0.1" interfaces
# using "." as separator:
net.ipv6.conf.eth0.use_tempaddr = 1
net.ipv6.conf.eth0/1.use_tempaddr = 1
# using "/" as separator:
net/ipv6/conf/eth0/use_tempaddr = 1
net/ipv6/conf/eth0.0/use_tempaddr = 1
Settings with variables:
# using "." as separator:
net.ipv6.conf.$SYSCTL_IF.use_tempaddr = 1
# using "/" as separator:
net/ipv6/conf/$INTERFACE/use_tempaddr = 1
To test your ifsysctl-eth0 or ifsysctl file, use:
/etc/sysconfig/network/scripts/ifup-sysctl eth0 -o debug
BUGS
Please report bugs at <https://bugzilla.novell.com/>
AUTHOR
Marius Tomaschewski <mt@suse.de>
SEE ALSO
ifup(8) ifcfg(5) sysctl(8)
sysconfig December 2009 IFSYSCTL(5)