10 More Discussions You Might Find Interesting
1. Hardware
Dear all,
I am setting up a new Ethernet network at home, I am going to have a good 100 Mbps internet connection (optic fiber) with a modem that have a gigabit ethernet card.
I would like to to measure the speed of data transmission between several servers that are going to be connected to the... (2 Replies)
Discussion started by: freddie50
2 Replies
2. Solaris
Hi Gurus of Solaris.
I have a problem yesterday when I was installing solaris in a x86 equipement
I attached some log that I capture when I try to resolve the problem
Any guru that can help please.
Any command or procedure that I can run, please advice me
Regards
Andres (10 Replies)
Discussion started by: andresguillen
10 Replies
3. AIX
Hi,
is it possible to find out network utilization of etherenet card in %?
Regards,
Manoj (2 Replies)
Discussion started by: manoj.solaris
2 Replies
4. Solaris
Hi Group,
I Have just installed quad card in my V440 machine,
I am facing problem I cn just ping its ce0 card only rest of the cards are not ping able,
here is details of my machine.
ifconfig -a
lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index
1
... (2 Replies)
Discussion started by: sameergrover
2 Replies
5. IP Networking
What command do I use to show mw the ethernet card, I have tried ipconfig -a (1 Reply)
Discussion started by: dhlopomo
1 Replies
6. Solaris
I have a Quad Ethernet card in a 220R. 2 ports activated. Each has its own hostname file and both hostnames are in the hosts file. I want both ports to have the same IP address so we can use the 2nd port in case we lose communication on the port. On bootup, the box gives me:
SIOCSLIFFLAGS:... (5 Replies)
Discussion started by: hshapiro
5 Replies
7. SCO
Installed a replacement 3com pci card on an ibm PC 300 GL, running OpenServer 6.0 , brought up system, and recieved this message:
Fsstat:/dev/boot mounted
Mounted /stand filesystem
System auditing is not enabled.
Dlpid:Unable to open network adapter driver (/dev/mdi/r8e0)
Dlpid:No such... (0 Replies)
Discussion started by: tazmss1
0 Replies
8. UNIX for Dummies Questions & Answers
I am an extreme novice trying to learn Linux. I have redhat 9 installed in a computer I built specifically to install and learn linux. I have an asus a7v8x-x motherboard with the realtek 10/100 mbps ethernet card. I also installed a Jaht adapter jn-1110r32c ethernet card. I cannot get the... (2 Replies)
Discussion started by: Tony Empire
2 Replies
9. IP Networking
I have searched this forum for solution and have drawn a blank... so I come to you for help :)
I an a Win XP user that has no problem getting on internet when I am on that OS (currently on it right now ;)). I installed red hat 9 and when I use that OS, I cannot get a connection. I ran the... (10 Replies)
Discussion started by: Minnesota Red
10 Replies
10. Filesystems, Disks and Memory
Hi,
How can i check the speed of the Ethernet card that my Sun server has and also how can i change it to full Duplex if it is set to half duplex? What is the file that takes care of this? (3 Replies)
Discussion started by: i2admin
3 Replies
ip6_setup(8) System Manager's Manual ip6_setup(8)
NAME
ip6_setup - IPv6 configuration program
SYNOPSIS
/usr/sbin/ip6_setup
DESCRIPTION
The ip6_setup utility allows you to configure the IPv6 networking software on your system.
To run ip6_setup, enter the following command and then answer the questions: # ip6_setup
You must know your Internet Protocol Version 6 (IPv6) address. If your network uses subnet routing, you must know the subnet mask for your
network. The network manager should be able to provide you with the information that you need.
After the ip6_setup command completes, the network services on the system can be restarted manually with the following command: #
/usr/sbin/rcinet restart
Before you restart the network services with the preceding command, warn the users that the network services on the system are being
removed. File systems that were not mounted using the /etc/fstab file or the automount command must be unmounted with the unmount command.
You must remount these file systems using the mount command after the network is started on your system.
Alternatively, you can reboot the system with the following command: # /usr/sbin/shutdown -r now
FILES
Specifies the host name file. Specifies the environment variables that define the network configuration on your system. Specifies the
trusted hosts file. Specifies the network name file. Specifies Internet routing information. Specifies Internet routing information.
SEE ALSO
Commands: mount(8), rcinet(8)
Files: gateways(4), hosts(4), hosts.equiv(4), networks(4), routes(4).
Network Administration
ip6_setup(8)