9 More Discussions You Might Find Interesting
1. IP Networking
four interfaces with ifconfig
all interfaces have the same mac. If is not set for unique.
but it still works.
what difference does it make to have all macs the same or different? (4 Replies)
Discussion started by: rrodgers
4 Replies
2. AIX
Hello, hopefully someone can help me out with this, I have created a virtual Ethernet adapter on the VIO but would like to add it to my new LPAR.
On my VIO only my disk is mapped.
$ lsmap -all
SVSA Physloc Client Partition ID
--------------- --------------------------------------------... (5 Replies)
Discussion started by: audis$
5 Replies
3. AIX
All
I am trying allocate an IVE to an LPAR (not a VIO) running AIX 7.1. I am getting the error:
HSCL068A
Explanation
Logical port can not be assigned to Logical Partition because this Logical Partition is not the promiscuous LPAR for the physical port.
Has anyone encountered this... (1 Reply)
Discussion started by: johnf
1 Replies
4. Programming
Hi,
I found on linuxgazette.net/93/bhaskaran.html page very useful sample of virtual driver (not connected to real hardware).
I try to compile it with no effect.
So:
I got fresh Ubuntu 9.10 (kernel 2.6.31-14)
My source is saved in networkAdapter.c file in /usr/src/myModules directory.
I... (21 Replies)
Discussion started by: Chrisdot
21 Replies
5. UNIX for Dummies Questions & Answers
Hi guys,
I got one problem which I definetily no idea.
What would the physical address be for virtual address?
1) 2ABC
2) 3F4B
Here is the page table:see attached
Thank you sos sososososso much!! (0 Replies)
Discussion started by: lemon_06
0 Replies
6. IP Networking
Hi ,
by default the physical interface (eth1) and virtual interface eth1:0 will be having same mac address, is there any way we can assign separate mac addresses for both the interfaces.
would some one help me out in this.
Thanks
Gopi (1 Reply)
Discussion started by: Gopi Krishna P
1 Replies
7. IP Networking
Hi All,
Sorry if this is not the correct forum to answer.
But hope somebody can help me...
For these two types of network adapter:
Intel(R) PRO/1000 MT Server Adapter
Intel(R) PRO/1000 MT Dual Port Network Adapter
How many IP addresses can be configured on it at the same time?
System... (3 Replies)
Discussion started by: wilsonSurya
3 Replies
8. AIX
Hello,
Searched in all IBM Redbooks and on the internet and couldn't find anything about the new feature of POWER 6 which Virtual Fibre ( Fiber ) channel adapter.
It is similar to virtual scsi adapter.
In my client partition I created the virtual Fibre Adapter mapped it with the VIO... (1 Reply)
Discussion started by: filosophizer
1 Replies
9. UNIX for Dummies Questions & Answers
I have installed in the server a quad ethernet adapter, I'm using two interfaces with two different IP networks, both interfaces are connected to a switch, the switch report that is receiving the same MAC address in both ports so must of the times I have connectivity problems.
Any idea to change... (1 Reply)
Discussion started by: mono673
1 Replies
HME(4) BSD Kernel Interfaces Manual HME(4)
NAME
hme -- Sun Microelectronics STP2002-STQ Ethernet interfaces device driver
SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file:
device miibus
device hme
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
if_hme_load="YES"
DESCRIPTION
The hme driver supports Sun Microelectronics STP2002-STQ ``Happy Meal Ethernet'' Fast Ethernet interfaces.
All controllers supported by the hme driver have TCP checksum offload capability for both receive and transmit, support for the reception and
transmission of extended frames for vlan(4) and a 128-bit multicast hash filter.
HARDWARE
The hme driver supports the on-board Ethernet interfaces of many Sun UltraSPARC workstation and server models.
Cards supported by the hme driver include:
o Sun PCI SunSwift Adapter (``SUNW,hme'')
o Sun SBus SunSwift Adapter (``hme'' and ``SUNW,hme'')
o Sun PCI Sun100BaseT Adapter 2.0 (``SUNW,hme'')
o Sun SBus Sun100BaseT 2.0 (``SUNW,hme'')
o Sun PCI Quad FastEthernet Controller (``SUNW,qfe'')
o Sun SBus Quad FastEthernet Controller (``SUNW,qfe'')
NOTES
On sparc64 the hme driver respects the local-mac-address? system configuration variable which can be set in the Open Firmware boot monitor
using the setenv command or by eeprom(8). If set to ``false'' (the default), the hme driver will use the system's default MAC address for
all of its devices. If set to ``true'', the unique MAC address of each interface is used if present rather than the system's default MAC
address.
Supported interfaces having their own MAC address include on-board versions on boards equipped with more than one Ethernet interface and all
add-on cards except the single-port SBus versions.
SEE ALSO
altq(4), intro(4), miibus(4), netintro(4), vlan(4), eeprom(8), ifconfig(8)
Sun Microelectronics, STP2002QFP Fast Ethernet, Parallel Port, SCSI (FEPS) User's Guide,
http://mediacast.sun.com/users/Barton808/media/STP2002QFP-FEPs_UG.pdf, April 1996.
HISTORY
The hme driver first appeared in NetBSD 1.5. The first FreeBSD version to include it was FreeBSD 5.0.
AUTHORS
The hme driver was written by Paul Kranenburg <pk@NetBSD.org>.
BSD
June 14, 2009 BSD