10 More Discussions You Might Find Interesting
1. Red Hat
Dear All ,
Very recently we have configured Network bonding in our Linux Server Redhat Linux 5.x.
After configuring , we restarted the network services , the link was down after that , we could not login in to the Server.
So after that , we logged in to console and tried to... (2 Replies)
Discussion started by: jegaraman
2 Replies
2. Red Hat
I have one production system where my customized application runs.The applications require seamless network connectivity with different machines connected in LAN and WAN. As these applications are very critical, it is very much required to have a seamless network activity.The applications are... (4 Replies)
Discussion started by: Anjan Ganguly
4 Replies
3. IP Networking
HI all,
First post on the forum, and my first proper project on the Paspberry Pi, so sorry if this is in the wrong place.
I am trying to turn my Pi in to a 3G/4G Bonding router. I have been researching and trying this for a week or so now. The basic plan is to have up to 6 ZTE MF823 USB... (0 Replies)
Discussion started by: elliottlc
0 Replies
4. Red Hat
Does anyone know if it's possible to bond two bonds together? My situation is I have two older Cisco switches that cannot carry a LACP (bond level 4) aggregated between them, but separate aggregates can be setup on the switches themselves. In order to have redundancy of two switches I would... (0 Replies)
Discussion started by: christr
0 Replies
5. Red Hat
I am new to linux. I have a falconstor CDP installation which runs on RHEL 5.5 (Tikanga). There is a vendor option to bond nics in either 802.3ad or round robin, I choose 802.3ad. The server is connected to a Cisco 3750 switch.
The problem is dropped packets and eth03 wont come up in the PO... (0 Replies)
Discussion started by: tjcooper
0 Replies
6. Linux
I need to enable Ethernet Bonding on three systems, connected together via switch. What I tried ended up with failure, slaves cannot be detected n added to bon0.
Here's what I did:
created file /etc/modprobe.d/bonding.d and added the following to it:
alias bond0 bonding
options bonding... (2 Replies)
Discussion started by: dr_mabuse
2 Replies
7. Red Hat
Hi,
What is IP bonding in Linux.
What are its advantages
How to create a IP bonding in redhat Linux. (1 Reply)
Discussion started by: chetansingh23
1 Replies
8. IP Networking
I’m familiar with load balancing.. but Is it possible to actually bond multiple DSL lines together? I hear of ways to bond using MLPPP but that requires support from an ISP. Is there a way to actually bond without support from my ISP, or use say a cable modem and a DSL line together for faster... (0 Replies)
Discussion started by: harley313
0 Replies
9. HP-UX
userA and userB are two non-root accounts on HP-UX box. userA creates ssh tunnel (local forward) to some different host. Will userB be able to use that tunnel? What about remote forward? If not, what OS mechanism will prevent it from happening? Unfortunately I am unable to create this setup at this... (0 Replies)
Discussion started by: vkleban
0 Replies
10. UNIX for Advanced & Expert Users
Here is the scenario:
I use an OpenBSD 2.9 box as my firewall and gateway at the house. One of the boxes behind my OpenBSD box is my FreeBSDBox.
I would like to be able to use port forwarding with SSH to enable a secure connection from work to the OpenBSD box and to have the OpenBSD box... (6 Replies)
Discussion started by: auswipe
6 Replies
FINGER(1) General Commands Manual FINGER(1)
NAME
finger - user information lookup program
SYNOPSIS
finger [ options ] name ...
DESCRIPTION
By default finger lists the login name, full name, terminal name and write status (as a `*' before the terminal name if write permission is
denied), idle time, login time, and office location and phone number (if they are known) for each current UNIX user. (Idle time is minutes
if it is a single integer, hours and minutes if a ':' is present, or days and hours if a 'd' is present.)
A longer format also exists and is used by finger whenever a list of people's names is given. (Account names as well as first and last
names of users are accepted.) This format is multi-line, and includes all the information described above as well as the user's home
directory and login shell, any plan which the person has placed in the file .plan in their home directory, and the project on which they
are working from the file .project also in the home directory.
Finger may be used to lookup users on a remote machine. The format is to specify the user as ``user@host.'' If the user name is left off,
the standard format listing is provided on the remote machine.
Finger options include:
-m Match arguments only on user name.
-l Force long output format.
-p Suppress printing of the .plan files
-s Force short output format.
FILES
/etc/utmp who file
/etc/passwd for users names, offices, ...
/usr/adm/lastlog last login times
~/.plan plans
~/.project projects
SEE ALSO
chfn(1), w(1), who(1).
AUTHOR
Earl T. Cohen
BUGS
Only the first line of the .project file is printed.
There is no way to pass arguments to the remote machine as finger uses an internet standard port.
4th Berkeley Distribution May 10, 1986 FINGER(1)