RedHat/Centos Disable IPv6 Networking

8 More Discussions You Might Find Interesting

1. IP Networking

Centos/Redhat 7 - Team or Bond

Hello my dears, I preparing system running linux. I found that team is advantage than bond with the option "load-balancing for LACP support" and some minor advantages. 8.3. Comparison of Network Teaming to Bonding - Red Hat Customer Portal. But what exactly meaning of this option I don't...

2. Red Hat

How can i configure ipv6 on centos?

HI Forum, i was trying to configure ipv6 on my centos box with 2 physical interface bonded as bond0. what all things need to change? Regards, Ben

3. Red Hat

Help with setting up Networking for XEN on CentOS 5.9

Hey guys, I've reached the point of setting up VM's on XEN but the net installations seem to be failing when I am in the netinstall on the actual VM, so this leads me to believe that the networking on the host machine is not set up correctly. I am running CentOS 5.9 along with XEN and was just...

4. Solaris

Solaris 11 disable IPv6

I've new installed Solaris 11 on Sparc T4-1. I'd like to disable IPv6 but with no luck. lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1 inet 127.0.0.1 netmask ff000000 net0: flags=1000803<UP,BROADCAST,MULTICAST,IPv4> mtu 1500 index 2 inet...

5. UNIX and Linux Applications

Konqueror disable IPv6

Does anyone know how to disable IPv6 in Konqueror in Fedora?

6. Red Hat

IPv4 and IPv6 Related Question to CentOS VMs

Hello, I was wondering if it would be possible to run two VMs one with services for IPv4 and the other one with services for IPv6. The main physical system would be connected to a IPv6 switch. I think it should be fine but I would like to hear out your comments.

7. UNIX for Dummies Questions & Answers

problem of networking in centos

Hello, I am using dual boot of linux, one is ubuntu and the other is one is centos. I have three NIC's and only one of them connected with cable. The thing is that when I boot from the ubuntu, it does recognize it and I am connected to the Internet. When I boot from the centos I am not...

8. Linux

HOW TO DISABLE SIT0 in REDHAT LINUX 5.1

Hi All, I want to configure static IP4 address in my Linux system. I just found sit0 is enabled in my system. ifconfig -a returns sit0 Link encap:IPv6-in-IPv4, but there is no eth0. I tried with $ system-config-network & and changed static IP Add: 192.168.1.10 but no result after...

LEARN ABOUT SUSE

ifcfg-vlan

IFCFG-VLAN(5)						       Network configuration						     IFCFG-VLAN(5)

NAME

       ifcfg-vlan - virtual LAN interface configuration

SYNOPSIS

       /etc/sysconfig/network/ifcfg-vlan*

Virtual LANs (802.1q)
       To setup a vlan interface you need a configuration file that contains at least the mandatory

       ETHERDEVICE
	      variable with the real interface used for the virtual LAN.

       Further, it may contain the optional

       VLAN_ID
	      variable that specifies the VLAN ID.

       By default and when the VLAN_ID variable is not set, the number at the end of the interface name is the VLAN ID.

       Preferably the interface name and the configuration file follow the VLAN interface name scheme (type), that is either:
	      ifcfg-vlan<VLAN-ID> (e.g. ifcfg-vlan42)

	      or

	      ifcfg-name.<VLAN-ID> (e.g. ifcfg-eth0.42)

       The VLAN-ID can be also 0-padded (e.g. ifcfg-vlan0042 or ifcfg-eth0.0042).

       Also  in case of custom names, trailing digits are interpreted as VLAN-ID by default (e.g. ifcfg-dmz42). When VLAN_ID is set in the config,
       the interface name have any name (e.g. ifcfg-foobar).

       Note: The drawback of custom interface names and VLAN_ID usage is, that a rename of the interface is required and  that	they  violate  the
       name scheme.

       The  real  interface will be set UP automatically and doesn't need a config file in case of a physical interface. But without a config file
       YaST will consider this interface as unused, if will not follow hotplug	events	and  you're  unable  to  apply	any  settings,	e.g.  ETH-
       TOOL_OPTIONS. To avoid that, provide an config file with at least STARTMODE='auto'.

       The  rest  of  the VLAN interface IP and routes configuration do not differ from ordinary interfaces. See also man ifcfg and man routes for
       details.

EXAMPLES

       Sets up vlan3 vlan interface on top of eth0:

	      ifcfg-vlan3
		 STARTMODE='auto'
		 ETHERDEVICE='eth0'
		 IPADDR='192.168.3.27/24'

       Sets up eth0.3 vlan interface on top of eth0:

	      ifcfg-eth0.3
		 STARTMODE='auto'
		 ETHERDEVICE='eth0'
		 IPADDR='192.168.3.27/24'

       Sets up lan1 vlan interface with ID 42 on top of eth0:

	      ifcfg-lan1
		 STARTMODE='auto'
		 ETHERDEVICE='eth0'
		 VLAN_ID='42'
		 IPADDR='192.168.3.27/24'

BUGS

       Please report bugs at <http://www.suse.de/feedback>

AUTHOR

       Christian Zoz <zoz@suse.de>
       Michal Svec <msvec@suse.cz>
       Bjoern Jacke
       Mads Martin Joergensen <mmj@suse.de>
       Michal Ludvig <mludvig@suse.cz>
       Marius Tomaschewski <mt@suse.de>

SEE ALSO

       routes(5), ifcfg(5), ifup(8).

sysconfig							    August 2004 						     IFCFG-VLAN(5)

IP Networking