8 More Discussions You Might Find Interesting
1. IP Networking
Hello my dears,
I preparing system running linux. I found that team is advantage than bond with the option "load-balancing for LACP support" and some minor advantages.
8.3. Comparison of Network Teaming to Bonding - Red Hat Customer Portal.
But what exactly meaning of this option I don't... (1 Reply)
Discussion started by: tien86
1 Replies
2. Red Hat
HI Forum,
i was trying to configure ipv6 on my centos box with 2 physical interface bonded as bond0.
what all things need to change?
Regards,
Ben (0 Replies)
Discussion started by: bentech4u
0 Replies
3. Red Hat
Hey guys, I've reached the point of setting up VM's on XEN but the net installations seem to be failing when I am in the netinstall on the actual VM, so this leads me to believe that the networking on the host machine is not set up correctly. I am running CentOS 5.9 along with XEN and was just... (0 Replies)
Discussion started by: mccabec123
0 Replies
4. Solaris
I've new installed Solaris 11 on Sparc T4-1.
I'd like to disable IPv6 but with no luck.
lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
net0: flags=1000803<UP,BROADCAST,MULTICAST,IPv4> mtu 1500 index 2
inet... (6 Replies)
Discussion started by: samer.odeh
6 Replies
5. UNIX and Linux Applications
Does anyone know how to disable IPv6 in Konqueror in Fedora? (5 Replies)
Discussion started by: cokedude
5 Replies
6. Red Hat
Hello,
I was wondering if it would be possible to run two VMs one with services for IPv4 and the other one with services for IPv6. The main physical system would be connected to a IPv6 switch.
I think it should be fine but I would like to hear out your comments. (1 Reply)
Discussion started by: svalenciatech
1 Replies
7. UNIX for Dummies Questions & Answers
Hello,
I am using dual boot of linux, one is ubuntu and the other is one is centos.
I have three NIC's and only one of them connected with cable.
The thing is that when I boot from the ubuntu, it does recognize it and I am connected to the Internet.
When I boot from the centos I am not... (6 Replies)
Discussion started by: programAngel
6 Replies
8. Linux
Hi All,
I want to configure static IP4 address in my Linux system. I just found sit0 is enabled in my system. ifconfig -a returns sit0 Link encap:IPv6-in-IPv4, but there is no eth0.
I tried with $ system-config-network & and changed static IP Add: 192.168.1.10 but no result after... (2 Replies)
Discussion started by: gohappy
2 Replies
IFNDP-PROXY(5) Network configuration IFNDP-PROXY(5)
NAME
ifndp-proxy[-<interface name>] - IPv6 NDP and IPv4 ARP proxy entries
SYNOPSIS
/etc/sysconfig/network/ifndp-proxy
/etc/sysconfig/network/ifndp-proxy-<interface name>
DESCRIPTION
These files contain IPv6 NDP and IPv4 ARP proxy settings, that should be applied using the ip neigh add proxy command documented in the
ip(8) manual page that provides a common interface for IPv4 and IPv6.
The NDP/ARP proxy is required, e.g. when IP addresses from the same subnet have to be used on the interface of the host as well as on
interfaces behind a (tunnel) interface and using a bridge is not an option.
Don't forget to enable forwarding and the NDP/ARP proxy by setting
net.ipv6.conf.<all|default|interface name>.proxy_ndp = 1
net.ipv6.conf.<all|default|interface name>.forwarding = 1
and/or
net.ipv4.conf.<all|default|interface name>.proxy_arp = 1
net.ipv4.conf.<all|default|interface name>.forwarding = 1
or
net.ipv4.ip_forward = 1
either as global all setting in the /etc/sysctl.conf file or using the ifsysctl(5) files, that allow per-interface setup.
Forwarding can be also enabled in the /etc/sysconfig/sysctl file using the IP_FORWARD and IPV6_FORWARD variables.
The proxy entries are added and deleted using the if-{up|down}.d/ndp-proxy script, every time after an involved interface has been set
up or down.
SYNTAX
The format of the ifndp-proxy file is:
<address> <address interface> <proxy interface list>
The format of the ifndp-proxy-<address interface> file is same to above, but allows also to omit the address interface by using a "-" as
placeholder inside of the file, because it is already available in the file name:
<address> <address interface | -> <proxy interface list>
Lines beginning with # and blank lines are ignored.
Each line defines to add a proxy NDP/ARP entry with the address of or behind address interface to all interfaces in the proxy interface
list.
EXAMPLES
Let's assume, your machine is connected via eth0 to a switch with the networks 2001:db8:abba::/64 and 192.168.100.1/24 and is using the IP
address 1 itself. You'd like to use the addresses 11 and 12 e.g. for virtual machines behind the tap1 and tap2 interface, that is:
2001:db8:abba::1/64 -- local eth0 address
2001:db8:abba::11/64 -- address behind tap1
2001:db8:abba::12/64 -- address behind tap2
192.168.100.1/24 -- local eth0 address
192.168.100.11/24 -- address behind tap1
192.168.100.12/24 -- address behind tap2
then set up the following entries in the ifndp-proxy file:
2001:db8:abba::1 eth0 tap1 tap2
2001:db8:abba::11 tap1 eth0 tap2
2001:db8:abba::12 tap2 eth0 tap1
192.168.100.1 eth0 tap1 tap2
192.168.100.11 tap1 eth0 tap2
192.168.100.12 tap2 eth0 tap1
additionally to the routing entries in the routes or ifroute-<interface name> files.
BUGS
Please report bugs at <https://bugzilla.novell.com/>
AUTHOR
Marius Tomaschewski <mt@suse.de>
SEE ALSO
ifup(8) ifcfg(5) ifsysctl(8)
sysconfig December 2009 IFNDP-PROXY(5)