8 More Discussions You Might Find Interesting
1. IP Networking
Hello my dears,
I preparing system running linux. I found that team is advantage than bond with the option "load-balancing for LACP support" and some minor advantages.
8.3. Comparison of Network Teaming to Bonding - Red Hat Customer Portal.
But what exactly meaning of this option I don't... (1 Reply)
Discussion started by: tien86
1 Replies
2. Red Hat
HI Forum,
i was trying to configure ipv6 on my centos box with 2 physical interface bonded as bond0.
what all things need to change?
Regards,
Ben (0 Replies)
Discussion started by: bentech4u
0 Replies
3. Red Hat
Hey guys, I've reached the point of setting up VM's on XEN but the net installations seem to be failing when I am in the netinstall on the actual VM, so this leads me to believe that the networking on the host machine is not set up correctly. I am running CentOS 5.9 along with XEN and was just... (0 Replies)
Discussion started by: mccabec123
0 Replies
4. Solaris
I've new installed Solaris 11 on Sparc T4-1.
I'd like to disable IPv6 but with no luck.
lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
net0: flags=1000803<UP,BROADCAST,MULTICAST,IPv4> mtu 1500 index 2
inet... (6 Replies)
Discussion started by: samer.odeh
6 Replies
5. UNIX and Linux Applications
Does anyone know how to disable IPv6 in Konqueror in Fedora? (5 Replies)
Discussion started by: cokedude
5 Replies
6. Red Hat
Hello,
I was wondering if it would be possible to run two VMs one with services for IPv4 and the other one with services for IPv6. The main physical system would be connected to a IPv6 switch.
I think it should be fine but I would like to hear out your comments. (1 Reply)
Discussion started by: svalenciatech
1 Replies
7. UNIX for Dummies Questions & Answers
Hello,
I am using dual boot of linux, one is ubuntu and the other is one is centos.
I have three NIC's and only one of them connected with cable.
The thing is that when I boot from the ubuntu, it does recognize it and I am connected to the Internet.
When I boot from the centos I am not... (6 Replies)
Discussion started by: programAngel
6 Replies
8. Linux
Hi All,
I want to configure static IP4 address in my Linux system. I just found sit0 is enabled in my system. ifconfig -a returns sit0 Link encap:IPv6-in-IPv4, but there is no eth0.
I tried with $ system-config-network & and changed static IP Add: 192.168.1.10 but no result after... (2 Replies)
Discussion started by: gohappy
2 Replies
SMPPPD(8) SMPPPD SMPPPD(8)
NAME
smpppd - SuSE Meta PPP Daemon
DESCRIPTION
smpppd is a daemon that controls several internet connections.
Use a frontend like cinternet , qinternet or kinternet to control the connections and retrieve status informations. Those frontends can
also run on different hosts.
The configuration of the dialup connections is done by YaST2 but there are some additional options available in the file /etc/smpppd.conf.
smpppd is not intended for direct use. Use rcsmpppd instead.
OPTIONS
These options are recognized by smpppd.
--detach
Detach from the controlling terminal. This is the default.
--nodeatch
Don't detach from the controlling terminal.
-d, --debug
Turn on debugging.
--version
Show program version and exit.
--help Show help information and exit.
BUGS
ISDN support is poor.
SIGNALS
SIGHUP Reload the configuration.
FILES
/etc/smpppd.conf
Basic configuration.
/etc/sysconfig/network/ifcfg-*
Configuration files for the interfaces.
/etc/sysconfig/network/providers/*
Configuration files for the providers.
/var/run/smpppd/control
Socket to communicate with local frontends.
/var/run/smpppd/ifcfg-*
Sockets to communicate with backends.
SEE ALSO
kinternet, qinternet, accounting(1), cinternet(1), wvdial(1), smpppd.conf(5), pppd(8), smpppd-ifcfg(8).
AUTHOR
Arvin Schnell <arvin@suse.de>
SuSE September 2003 SMPPPD(8)