It is perhaps a silly question but have ran modprobe bonding ?
Hi Peasant,
Yes i have ran modprobe bonding. But the issue i am facing that it works fine when system boots up but ASA i restart the network service the whole thing stops, the bond0 interface never comes up.
Finally i was able to resolve the issues i was facing in setting up Channel Bonding. It is working now but i am not very much sure about the results if they are correct.
I used two cars eth7 and eth8 to make a bond0 interface. The IP of the bond0 interface is 192.168.30.1. Now i try to ping this machine from my second test machine which has IP of 192.168.30.3 and it works fine. Now i try bringing the interface eth8 down using "ifdown eth8" and then ping again from test machine and it is successful, and then brought the interface eth8 again up using ifup eth8.
Now if i repeat the same for eth7 the ping stops working i.e. bringing eth7 down and keeping eth8 up and then ping from test machine i do not get ping responses even when one of the two bonded interfaces is up i.e. interface eth8 is up.
The Bonded interface bond0 is setup in round-robin mode(mode=0). I tried using the mode=1 also but got same results.
So can somebody please tell if it is working as it should work or there is some discrepancy in results.
Here are the config files
Network Interfaces config files
Thanks
Rohit
Moderator's Comments:
Please use [code] tags instead of [quote] tags for code and samples
Last edited by Scrutinizer; 04-23-2012 at 07:07 PM..
hi everone
i am experiencing disconnectivity from storage to My database machines. i have doubt on my FC cards in my sparc T4-2 machines. i want to know how should i check from my solaris that whether the cards are ok or not because once the disks get disconnect from SAN so it come back again but... (5 Replies)
Respected Members,
We encountered an issue during node reboot when eth1 and eth5 of bond1 were behaving unusual(both eth1 and eth5 were in unknown states and ifdown and ifup were used to rectify). Please find the messages and configuration files as below and please let me know for any other... (0 Replies)
Hi Everyone,
Is it possible to configure bonding over bonded interface in AIX?
For example:
server has for NIC port:
ent0
ent1
ent2
ent3
First I create a EtherChannel ent4 from ent0 and ent1.
and then I create a EtherChannel ent5 from ent2 and ent3.
Can I create a EtherChannel... (1 Reply)
Hi,
I have created a bonding bond1 interface with 6 Eth , mode=4. Recently i have changed my old ipv6 to new one and tried to restart as well as reload network service. Post which i can see old as well as changed ipv6 in ifconfig command output. Below are few files and command output for your... (1 Reply)
I am facing problems with native multipath of the OS RHEL 6.5 (32-bit). One of the two paths of random Logical disks are not going neither failing back unless we reboot the system.what could be the reason? (1 Reply)
I have one production system where my customized application runs.The applications require seamless network connectivity with different machines connected in LAN and WAN. As these applications are very critical, it is very much required to have a seamless network activity.The applications are... (4 Replies)
HI all,
First post on the forum, and my first proper project on the Paspberry Pi, so sorry if this is in the wrong place.
I am trying to turn my Pi in to a 3G/4G Bonding router. I have been researching and trying this for a week or so now. The basic plan is to have up to 6 ZTE MF823 USB... (0 Replies)
Hi team,
I'm running into a problem configuring bonding on an CentOS 64bit on DELL Server. I'm connecting eth0 and eth1
to a Cisco 2948 (CatOS 8.1(3)) and receiving flapping notices. The
ethernet address is that of the primary interface. I have tried
several different modes,... (3 Replies)
Hi All Linux Experts ,
Need Urgent help , im using RHEL6.2 Santiago , While playing Song its not playing Properly its jerking Voice breaking breaking ... Cant Hear Properly , And im using Intel DG61HO Motherboard With intel i3 Processor , Please Help me to get fixed this issue ... And cant... (4 Replies)
Hello,
I've been using mode 4 with four slaves, however looking at ifconfig showed that the traffic was not balanced correctly between the interfaces, the outgoing traffic has been alot higher on the last slave.
Example:
eth0 RX 123.2 GiB TX 22.5 GiB
eth1 RX 84.8 GiB TX 8.3 GiB
eth2... (3 Replies)