10 More Discussions You Might Find Interesting
1. IP Networking
hi guys
i have a simple question !
i have two ips . a valid and internal(172.16.11.2)
i want to use port forwarding to forward any request to valid IP port 8001 to internal ip port 80 .
i use this rule :
sysctl -w net.ipv4.ip_forward=1
iptables -t nat -A PREROUTING -p tcp... (1 Reply)
Discussion started by: mhs
1 Replies
2. HP-UX
Hi,
I wanted to configure new iscsi port on HPUX system, i added the target port address and configured it, once done, went to array side and searched for that host iqn number , but was nt able to find the same, came to host, then when i ran "iscsiutil -pVS" command it gave me below result
... (0 Replies)
Discussion started by: Vinay Kumar D
0 Replies
3. AIX
Hi Admins,
I am having a whole system lpar in open firmware state on HMC.
How can I bring it to running state ?
Let me know. Thanks. (2 Replies)
Discussion started by: snchaudhari2
2 Replies
4. Red Hat
Dear All,
I have my HP Data Protector installed on the backup server.
I want to connect this backup server with the client server through
telnet port 5555 like below
telnet < ipaddress of client> 5555
But when I try like this , it says ...Connection refused ...unable to connect to... (0 Replies)
Discussion started by: jegaraman
0 Replies
5. HP-UX
I'm facing some strange HP-UX behavior. I have a small SAN with one HP server, two Cisco SAN switches and one HP tape library connected. When I issues port reset, syslog shows the following:
Oct 15 07:34:51 terumos-bckp-srv2 vmunix: Target path (class=tgtpath, instance=12) has gone online. ... (2 Replies)
Discussion started by: Sapfeer
2 Replies
6. Programming
Hi,
In my application,I need to monitor the devices connected through serial port in solaris sparc 9 OS.I used c and java code for it and I am able to do the same but the problem comes when I restart the system and the open my application and try to monitor it.but I m unable to monitor the... (2 Replies)
Discussion started by: smartgupta
2 Replies
7. AIX
On AIX platform we are having Weblogic 8.1 as the middleware for an application.
The application is deployed in Weblogic on AIX platform and the server is having 2 dedicated listening ports for any incoming requests.
Output for netstat -an command for the port 30001 is as follows:-
tcp4... (7 Replies)
Discussion started by: subharai
7 Replies
8. UNIX for Dummies Questions & Answers
Hi,
Occasionally I am getting the port state in CLOSE_WAIT for long time in the solaris server. I am not sure is it application problem or not. Because we are using port 9009 for Tomcat process in our web application, some time when I start the application, the port 9009 is in CLOSE_WAIT... (0 Replies)
Discussion started by: mgmk.84
0 Replies
9. Solaris
Hi,
I am working with Sun Solaris 9 Sparc,Sun-Blade-100.In my application,I need to monitor the UPS using Serial port.
When I am using JRE 1.4 in my application,I am able to monitor it but when I am upgrading the JRE version from 1.4 to JRE1.6. I am not able to monitor the UPS.It is showing the... (1 Reply)
Discussion started by: smartgupta
1 Replies
10. HP-UX
Hi,all:
I want to boot an IA unix box from network, I am sure I set the DHCP and boot server, but it still failed !
It says : Client MAC Address: 00 18 FE 28 91 82 .....-
PXE-E16: Valid PXE offer not received.
Load of Core LAN Gb A failed: Not Found
I use the nettl command to trace the UDP... (0 Replies)
Discussion started by: bluepluto
0 Replies