10 More Discussions You Might Find Interesting
1. IP Networking
Add explicit route to 10.128.255.41/32 , gateway: 10.128.201.254
if not working, please try gateway through management port: 10.128.55.254
Just want to double confirm if this would be the correct command
#route add -net 10.128.255.41/32 10.128.201.254
And if didnt work
#route add... (1 Reply)
Discussion started by: Thilagarajan
1 Replies
2. Solaris
Hi Solaris Experts,
I am trying to add a routing table entry on our 5.1 Generic_144488-12 sun4v sparc Solaris 10 SUNW,SPARC-Enterprise-T5220 so that it is possible to ping 10.56.9.34 node
# netstat -rnv
IRE Table: IPv4
Destination Mask Gateway Device Mxfrg Rtt Ref
Flg Out In/Fwd ... (2 Replies)
Discussion started by: gjackson123
2 Replies
3. Solaris
I need to add a new route on solaris10 machine.
I want that all traffic on the 23 port (telnet) use 192.168.200.1 gateway.
How I do ?
Thank you in advance. (1 Reply)
Discussion started by: arfry
1 Replies
4. Solaris
Hi need to add 2 routes, one on each server.
I know the route add comand but I have always been given the parameters to put in.
I need a route in each of the 2 following servers to be able to ping and ssh between them. But how do i know which netmask to put in the route add command ?
In... (6 Replies)
Discussion started by: vettec3
6 Replies
5. Solaris
Hey Guys:
I am trying to add a route for assign a network interface to the traffic to/from a specific net, but allways to get the same system message : network is unreacheable
root@ColectorDMSCNT # route add net 200.44.46.0/24 161.196.84.196 1
add net 200.44.46.0/24: gateway... (2 Replies)
Discussion started by: aggadtech08
2 Replies
6. Solaris
Hi,
I am trying to add route command in Solaris 10 machine in the following fashion:
route add -host 10.8.112.10 180.144.1.250 -interface lo0:1
this command fails with an error "lo0:1: bad value"
I want to add a route to 10.8.112.10 that picks 180.144.1.250 as the gateway via the... (3 Replies)
Discussion started by: sudhir_shet
3 Replies
7. IP Networking
I have a system that i want to reach via a vpn created vi a fierwall.The fierwall in an other system.
The ip i am trying to get to is 172.16.4.48
I need to get to it via the hme1 interface.
The vpn gateway has this ip 172.30.50.1
I need to clean up the routing table and make this work; or is it... (5 Replies)
Discussion started by: waterboy
5 Replies
8. HP-UX
Hi,
My H-UX box has the GW pointing to 10.10.10.1 and I need add it a new route pointing to 192.168.80.x with the GW 10.10.10.13
I tried with:
#route add 192.168.80.2 255.255.255.255 10.10.10.13
but I get: add net 192.168.80.0: gateway 255.255.255.0: Network is unreachable
I tried with... (4 Replies)
Discussion started by: efrenba
4 Replies
9. IP Networking
I have two networks connected by cisco routers. My first subnet is 192.168.0.0 and my second is 192.168.1.0.
My SCO unix machine is on the 192.168.1.0 subnet with an IP of 192.168.1.231. It can see the entire .1.0 subnet but nothing on the other network.
My cicso router(gateway) to the other... (6 Replies)
Discussion started by: agoodrich
6 Replies
10. AIX
Hello ,
We have 3 rs/6000 server's running aix on our local network, so each time I try to ping one of these servers we get a "network is down" error , I've been instructed to use to route add command which is ...
#route add server.ip router.ip
after this the ping command works fine ,... (6 Replies)
Discussion started by: cubicle^dweller
6 Replies
XINE-REMOTE(1) General Commands Manual XINE-REMOTE(1)
NAME
xine-remote - a small tool to connect xine remote control server.
SYNOPSIS
xine-remote [options]
DESCRIPTION
This manual page documents briefly the xine-remote tool.
xine-remote can replace a raw telnet connection to a xine remote control server. It use the readline facilities (completion, vi/emacs
shortcuts, command history, etc...). By default, it try to connect the localhost, using the default port (see xine(1)).
OPTIONS
The program follow the usual GNU command line syntax, with long ioptions starting with two dashes (`-'). A summary of options are included
below.
-H, --host <hostname>
Try to connect <hostname>.
-P, --port <port>
Try to connect the host using <port>.
-c, --command <command>
Send <command> to server then quit. The command should be single quoted if it contain spaces or special characters.
-n, --noconnect
Do not initiate the connection on startup.
-v, --version
Display version.
-h, --help
Display options summary.
COMMANDS
Few commands are available, which are used to open or close a connection:
? Display available commands (the xine-remote ones + server ones when connection is established).
help <command>
Display the purpose of <command>, if that is omitted, display available commands.
syntax <command>
Display the usage of <command>.
version
Display version.
open <server[:port]>
Open connection to server. A port can be optionally specified, using colon (:) separator.
close Close connection.
quit Leaving xine-remote.
SEE ALSO
xine(1).
AUTHOR
This manual page was written by Daniel Caujolle-Bert <f1rmb@users.sourceforge.net> for the xine project.
The xine project 2002-04-16 XINE-REMOTE(1)