howto start with gateway / router / masquerading

4 More Discussions You Might Find Interesting

1. UNIX for Beginners Questions & Answers

Howto auto boot SPARC | How to auto supply "start /SYS" and "start /SP/console" commands

When I power ON my T4-1, I got a prompt -> where I have to start /SYS and start /SP/console. How can I auto supply these two commands ?

2. UNIX for Beginners Questions & Answers

Inconsistency between RedHat 6.5 global gateway and single gateway leads to loss of default gateway

Dear friends I use RedHat 6.5, which sets the gateway in the configuration file / etc / sysconfig / network as GATEWAY = 192.168.1.26, and the gateway in the configuration file / etc / sysconfig / network-scripts / ifcfg-eth11 as GATEWAY = 192.168.1.256. The two gateways are different....

3. Linux

GNUGK-How to setup static gateway to gateway routing

Dear Sir I am a newbie in the world of IP telephony. I have been working with Asterisk PBX (SIP) and Cisco Call Manager (MGCP) but now I am learning on how to work GNUGK for H.323 Gatekeeper. I am having a problem, configuring static call routing on GNUGK in the section ...

4. UNIX for Dummies Questions & Answers

Remote Unix printing to my WinXP works with no router. How can I make it work through my router?

I set up remote printing on a clients Unix server to my Windows XP USB printer. My USB printer is connected directly to my PC (no print server and no network input on printer). With my Win XP PC connected to my cable modem (without the router), i can do lp -dhp842c /etc/hosts and it prints. I...

LEARN ABOUT DEBIAN

amttool

amttool(1)						      General Commands Manual							amttool(1)

NAME

       amttool - remotely control Intel AMT managed machines.

SYNOPSIS

       amttool host [ command ] [ arg(s) ]

DESCRIPTION

       amttool is a perl script which speaks SOAP to Intel AMT managed machines.  It can query informations about the machine in question and also
       send some commands for basic remote control.

       host is the hostname or IP address of the machine amttool should control.  command is an optional command.

       You must set fill AMT_PASSWORD environment variable with the AMT password.

       For more inforamtions on Intel AMT check amt-howto(7).

COMMANDS

       info   gather information (default).

       reset [ special ]
	      reset machine, with optional special command (see section below).

       powerup [ special ]
	      turn on machine.

       powerdown
	      turn off machine.

       powercycle [ special ]
	      powercycle machine.

       netinfo
	      print network configuration (requires AMT 2.5+).

       netconf if link [ ip mask gw [ dns1 [ dns2 ]]]
	      configure network interface (requires AMT 2.5+).	if is the interface handle, link the link policy.  If in doubt just feed  in  what
	      the  netinfo  command  prints.  ip is the IPv4 address, mask the netmask, gw the default gateway, dns1 and dns2 are the DNS Servers.
	      If no IP configuration is specified the tool tries to configure the machine in shared mac address mode with dhcp, otherwise in sepa-
	      rate mac address mode with static IP address.  Default for dns1 is the gateway address, for dns2 it is 0.0.0.0.

SPECIAL COMMANDS

       Special commands can optionally be specified for reset, powerup and powercycle.	They change the default boot behavior of the machine.

       bios   Asks for the BIOS boot messages being redirected to serial-over-lan.

       pxe    Network boot via PXE.

       hd     Boot from local disk.

       hdsafe Boot from local disk (safe mode).

       cd     Boot from CD/DVD.

       diag   Boot in diagnostics mode.

ENVIRONMENT

       AMT_PASSWORD
	      AMT password.

       AMT_DEBUG
	      Enable debug output.

SEE ALSO

       amtterm(1), gamt(1), amt-howto(7)

AUTHOR

       (c) 2007 Gerd Hoffmann <kraxel@redhat.com>

							     (c) 2007,08 Gerd Hoffmann							amttool(1)

IP Networking