Dose any know know where I can find the HPUX net-snmp depot file for HPUX b.11.11 I found the 11.23 version which of course will not install. Any help would be greatly appreciated thanks.
Hi All,
I have an issue with net-snmp communication from a monitoring server to HP UX server.
Following are the details
HP - UX server : 172.16.184.34
Monitoring Server : 172.16.5.57
(Solarwinds Application)I'm running HP-UX's snmp on udp port 161 and net-snmp on udp 1161.
... (0 Replies)
I have been trying to get net-snmp working on a HPUX box for over a week now. I do not think it should be this difficult. I must be missing a step. this morning I tried once again and now not even the native HPUX agent is working so I have no SNMP monitoring. So here is where I am at. Any help... (0 Replies)
I am trying to install net-snmp on an HPUX box. I am getting the fallowing error message when I try to run the snmpconf file. I installed the fallowing version of
net-snmp
net-snmp-5.0.10.2-HP-UX_B.11.11_9000_800.tar and my
HPUX box is version
HP-UX commnms B.11.11 U 9000/800... (2 Replies)
hello
I am running solaris 8 sparc.
I installed net-snmp 5.4.1 (compiled it from tar file).
When I do snmpwalk from another server, I receive a partial list of OIDs then it stops and gives 'timeout. No response...'
another snmpwalk will directly timeouts.
I compiled again the binaries... (1 Reply)
Hello,
we running on a hpux workstation hpux 11.11 ( model B180 L ) latest relaese from december 2001. now we would like to install an tool which will allow us to generate our own depots. this programm names mkpkg ( relaese 3.0 alpha 5 ) and we downloaded it from... (2 Replies)
snmp-ups(8) Network UPS Tools (NUT) snmp-ups(8)NAME
snmp-ups - Driver for RFC 1628 SNMP UPS equipment
NOTE
This man page only documents the hardware-specific features of the snmp-ups driver. For information about the core driver, see nutups-
drv(8).
SUPPORTED HARDWARE
Any UPS that is RFC 1628 (UPS MIB) compliant.
EXPERIMENTAL DRIVER
This driver has been tagged experimental and is not built by default.
REQUIREMENTS
This driver needs UCD SNMP, aka Net-SNMP installed to compile successfully. See http://www.net-snmp.org/ for more information.
On Red Hat 7.2, these packages are required:
ucd-snmp-devel-4.2.3-1, ucd-snmp-4.2.3-1, ucd-snmp-utils-4.2.3-1
You must install SNMP-UPS-MIB.txt in your MIBs directory - typically /usr/share/snmp/mibs/, but it may vary from system to system. You can
generate this from chapter 4 of RFC 1628 (see http://www.faqs.org).
EXTRA ARGUMENTS
This driver supports the following optional settings in the ups.conf(5):
community=name
Set community name (default = public)
snmp_version=version
Set SNMP version (default = v1, the other allowed value is v2c)
INSTALLATION
This driver is not built by default. You can build it by using "configure --with-drivers=snmp-ups" before calling make.
IMPLEMENTATION
The hostname of the UPS is specified with the "port" value in ups.conf, i.e.:
[snmp]
driver = snmp-ups
port = snmp-ups.example.com
community = public
snmp_version = v1
SUPPORTED VARIABLES
INFO_MFR UPS Manufacturer
INFO_MODEL UPS Model
INFO_FIRMREV Firmware/Software Version
INFO_STATUS OFF, OL, OB, BOOST, TRIM
INFO_BATTPCT Battery percentage
INFO_RUNTIME Predicted runtime on battery
INFO_BATTVOLT Battery Voltage
INFO_OUTVOLT Output Voltage
PLANNED SUPPORT
INFO_UTILITY Input Voltage
INFO_ACFREQ AC Frequency
INFO_UPSTEM UPS Temperature
INFO_LOADPCT Load Percentage
CMD_? Not determined
AUTHORS
Arnaud Quette, Hans Ekkehard Plesser
SEE ALSO
The core driver:
nutupsdrv(8)
Internet resources:
The NUT (Network UPS Tools) home page: http://www.exploits.org/nut/
NUT mailing list archives and information: http://lists.exploits.org/
Tue Oct 22 2002 snmp-ups(8)
