As discussed previously, though snmp is installed in my system basic commands in snmp for example snmpget and snmpwalk do not work, it gives error saying command not found. Please help me
Hey everyone!
So as i finished setting up my apache2 server, I wanted to look into some basic authentication for the web page. I found a great guide on apache.org. The problem now is, the htpasswd2 file that i need to create and store users, is in a weird format.
It is displaying as :
... (3 Replies)
Hello,
I want to install openssl-1.0.1c-1.aix5.1.ppc.rpm on IBM AIX 6.1 server machine and when I try to install the same as : rpm -ivh openssl-1.0.1c-1.aix5.1.ppc.rpmI get the error saying that it needs the following dependencies :
error: failed dependencies:
... (2 Replies)
I have dexx xps 14.I was installing rhel6.But the installation hanged at following step
initializing hardware detection.................
installion didnt go further (2 Replies)
Hi,
I am new to AIX, I have to install HP Open View on AIX OS and I would appreciate if anyone can guide me how to install it step be step, any pointer in the direction would also help.
I thank all in advance ! (1 Reply)
Hi all,
I tried to install Sun Solaris 10 on a X-86 based machine. I have dedicated entire diskspace to create auto partition. My hardware config is below:
Main Board : Asus
Processor : Intel 945 , 3 G/Hz
RAM : 1 Gigs
Diskspace : 80 Gigs
When I install, installation goes successful.... (1 Reply)
No unix/linux systems have worked on my computer
Problem: I have SATA hard drive and every time i get the error which says 'YOU HAVE NO HARD DRIVE'
wondering which i tried?
http://www.linuxiso.org/
so if you have dealt with this before, please reply
if you think you know then it might... (12 Replies)
I'm in the process of installing openbsd 3.2, the install appears to go ok but will not boot. So I tried the install again, when I opt to partition I noticed the disk the signature (in geometry) reads as 0x0 instead of 0xAA55. I'm using Lucas's 'Absolute OpenBSD' as my install guide together with... (3 Replies)
PEGASUS-RUN(1)PEGASUS-RUN(1)NAME
pegasus-run - executes a workflow that has been planned using *pegasus-plan*.
SYNOPSIS
pegasus-run [-Dproperty=value...][-c propsfile][-d level]
[-v][--grid*][rundir]
DESCRIPTION
The pegasus-run command executes a workflow that has been planned using pegasus-plan. By default pegasus-run can be invoked either in the
planned directory with no options and arguments or just the full path to the run directory. pegasus-run also can be used to resubmit a
failed workflow by running the same command again.
OPTIONS
By default pegasus-run does not require any options or arguments if invoked from within the planned workflow directory. If running the
command outside the workflow directory then a full path to the workflow directory needs to be specified.
pegasus-run takes the following options
-Dproperty=value
The -D option allows an advanced user to override certain properties which influence pegasus-run. One may set several CLI properties by
giving this option multiple times.
The -D option(s) must be the first option on the command line. CLI properties take precedence over the file-based properties of the
same key.
See the PROPERTIES section below.
-c propsfile, --conf propsfile
Provide a property file to override the default Pegasus properties file from the planning directory. Ordinary users do not need to use
this option unless the specifically want to override several properties
-d level, --debug level
Set the debug level for the client. Default is 0.
-v, --verbose
Raises debug level. Each invocation increase the level by 1.
--grid
Enable grid checks to see if your submit machine is GRID enabled.
rundir
Is the full qualified path to the base directory containing the planned workflow DAG and submit files. This is optional if the
pegasus-run command is invoked from within the run directory.
RETURN VALUE
If the workflow is submitted for execution pegasus-run returns with an exit code of 0. However, in case of error, a non-zero return value
indicates problems. An error message clearly marks the cause.
FILES
The following files are created, opened or written to:
braindump
This file is located in the rundir. pegasus-run uses this file to find out paths to several other files, properties configurations etc.
pegasus.?????????.properties
This file is located in the rundir. pegasus-run uses this properties file by default to configure its internal settings.
workflowname.dag
pegasus-run uses the workflowname.dag or workflowname.sh file and submits it either to condor for execution or runs it locally in a
shell environment
PROPERTIES
pegasus-run reads its properties from several locations.
RUNDIR/pegasus.??????????.properties
The default location for pegasus-run to read the properties from
--conf propfile
properties file provided in the conf option replaces the default properties file used.
$HOME/.pegasusrc
will be used if neither default rundir properties or --conf propertiesfile are found.
Additionally properties can be provided individually using the -Dpropkey=propvalue option on the command line before all other options.
These properties will override properties provided using either --conf or RUNDIR/pegasus.???????.properties or the $HOME/.pegasusrc
The merge logic is CONF PROPERTIES || DEFAULT RUNDIR PROPERTIES || PEGASUSRC overriden by Command line properties
ENVIRONMENT VARIABLES
PATH
The path variable is used to locate binaries for condor-submit-dag, condor-dagman, condor-submit,pegasus-submit-dag, pegasus-dagman and
pegasus-monitord
SEE ALSO pegasus-plan(1)AUTHORS
Gaurang Mehta <gmehta at isi dot edu>
Jens-S. Vockler <voeckler at isi dot edu>
Pegasus Team http://pegasus.isi.edu
05/24/2012 PEGASUS-RUN(1)
