10 More Discussions You Might Find Interesting
1. Solaris
i booted into maintenance mode
boot -- -s
from the console
I got the
Root password for system maintenance (control-d to bypass)
I did control -d
and then logged in
it told me that I was booting into boot -s
but after I did a control -d and logged in
who -r shows
... (9 Replies)
Discussion started by: goya
9 Replies
2. AIX
Hi this may be a easy question to answer but thanks in advance.
So I was able to download the VIOS media from IBM and currently I am burning it to a cd/dvd right now.
The steps I've collected so far are from the net. can you please confirm and add on to the steps if there are any steps... (0 Replies)
Discussion started by: Adnans2k
0 Replies
3. Solaris
Hi,
I have an issue with RPC bind service and its failing with status 1. any help would be much appreciated.
THanks (2 Replies)
Discussion started by: Yakub Humami
2 Replies
4. Solaris
:confused:
when i tried to look the status of DNS-client, it is in maintenance mode.....
Please tell me how to bring it back to online mode...PLEASE TELL ME STEP BY STEP.... PLEASE...
:wall: (2 Replies)
Discussion started by: vamshigvk475
2 Replies
5. Solaris
I have seen similar threads on this issue, but I have not seen a fix. Basically I am getting a lot of rcp bind errors. Below find the output of "svcs -xv". not sure where to begin:
# svcs -xv
svc:/network/rpc/bind:default (RPC bindings)
State: maintenance since Fri May 25 14:13:18 2012... (14 Replies)
Discussion started by: brownwrap
14 Replies
6. Solaris
Hi Guys,
I have a sunblade 1500. I booted the system and it booted to maintenance mode. How can I fix this?
Thanks lots (8 Replies)
Discussion started by: cjashu
8 Replies
7. Solaris
I have a Solaris 10 SunFire v880 machine and I'm having trouble with Samba.
Samba has worked on this machine but since the machine has been re-booted Samba has not worked.
Machine details are:
cat /etc/release
Solaris 10 10/08 s10s_u6wos_07b SPARC
Copyright 2008... (2 Replies)
Discussion started by: KenLynch
2 Replies
8. Solaris
Hi,
I have installed Hudson on a Solaris 11 server, using the installation instructions available at Paul Oswald: Hudson Solaris SMF Manifest.
When I perform svcs -l hudson, I get:
fmri svc:/application/hudson:default
name Hudson Continuous Build Server
enabled true... (4 Replies)
Discussion started by: JVerstry
4 Replies
9. Solaris
Hello All,
On solaris 10 server i could see the FTP service is in maintenance mode always :mad:
Could some assist?
svcs -xv
svc:/network/nfs/nlockmgr:default (NFS lock manager)
State: maintenance since Tue 28 Jul 2009 11:47:55 AM BST
Reason: Restarting too quickly.
See: Sun... (5 Replies)
Discussion started by: bullz26
5 Replies
10. Solaris
I had a power failure the other day and when my relatively new Solaris 10 machine rebooted it is thrown into maintenance mode.
I've found the following lines in the /var/adm/messages file, I'm assuming this is the root cause of the problem. However, I don't have the slightest idea on how to... (9 Replies)
Discussion started by: cheetobandito
9 Replies
BOOT.CONFIG(5) BSD File Formats Manual BOOT.CONFIG(5)
NAME
boot.config -- Configuration file for the boot blocks
DESCRIPTION
The boot.config file contains options for the FreeBSD boot block code.
When the FreeBSD boot loader runs, it searches the ``a'' slice of the boot partition for a boot.config file (as a result, slices which are
missing an ``a'' partition require user intervention during the boot process). If the boot.config file is found, its contents are used as
the default configuration options for the boot block code and are echoed to the system console.
A valid format of this file is to put BIOS drive number, a controller type, a unit number, a partition, a kernel file name, and any other
valid boot(8) option on a single line, as it is done at the ``boot:'' prompt.
The options related to the boot image selection described below and all the other options available for boot.config are documented in detail
in the boot(8) manual page.
FILES
/boot.config parameters for the boot blocks (optional)
EXAMPLES
The command:
# echo "-P" > /boot.config
will activate the serial console of FreeBSD.
The command:
# echo "1:ad(1,a)/boot/loader" > /boot.config
will instruct the second stage of boot(8) on the first disk to boot with the third boot(8) stage from the second disk.
The command:
# echo "1:ad(1,a)/boot/loader -P" > /boot.config
will do both of the above.
SEE ALSO
boot(8), loader(8)
AUTHORS
This manual page was written by Daniel Gerzo <danger@FreeBSD.org>.
BSD
May 13, 2007 BSD