4 More Discussions You Might Find Interesting
1. AIX
Hi, I have and IB RS/6000 machine running 32-bit AIX 4.3.3. We have a directory that is NFS mounted to this machine. Whenever I run the "ls" command in this directory, I get the following error: 0653-340 There is not enough memory available now
There was originally 512 MB of... (11 Replies)
Discussion started by: amp24
11 Replies
2. Solaris
I need to find out PSU info for some M class severs, normally prtdiag -v show's the relevant PS info, however these M classes don't seem to go down to that level !?
Anyone any ideas , no physical or console access available at this stage :(
thx... (3 Replies)
Discussion started by: itsupplies
3 Replies
3. HP-UX
Hello,
I am trying to move an HP UX from one locaion to another. The new location don't have any Fiber switches.
On the back of my server I see 2 RJ 45 for console management the other for networking , the server also has a fiber NIC card. When I disconnec the fiber and want to user regular... (1 Reply)
Discussion started by: ldaliosmane
1 Replies
4. UNIX for Advanced & Expert Users
Hello Everyone I run 4 HP 9000 servers with HP-UX 11.0 on all 4, with an Infomix Database. About 6 months ago one system starting acting real weird it will display the message that it lost power (which did not) and it would shutdown, Then roughly 30 seconds later it would then say power has... (4 Replies)
Discussion started by: JackieRyan26
4 Replies
volcheck(1) User Commands volcheck(1)
NAME
volcheck - checks for media in a drive and by default checks all floppy media
SYNOPSIS
volcheck [-v] [-i secs] [-t secs] pathname
DESCRIPTION
The volcheck utility tells Volume Management to look at each dev/pathname in sequence and determine if new media has been inserted in the
drive.
The default action is to volcheck all checkable media managed by volume management.
OPTIONS
The following options are supported:
-i secs Set the frequency of device checking to secs seconds. The default is 2 seconds. The minimum frequency is 1 second.
-t secs Check the named device(s) for the next secs seconds. The maximum number of seconds allowed is 28800, which is 8 hours. The fre-
quency of checking is specified by -i. There is no default total time.
-v Verbose.
OPERANDS
The following operands are supported:
pathname The path name of a media device.
EXAMPLES
Example 1: A sample of the volcheck command.
The following example
example% volcheck -v /dev/diskette
/dev/diskette has media
asks Volume Management to examine the floppy drive for new media.
The following example
example% volcheck -i 2 -t 600 /dev/diskette1 &
asks Volume Management if there is a floppy in the floppy drive every 2 seconds for 600 seconds (10 minutes).
FILES
/dev/volctl Volume Management control port
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWvolu |
+-----------------------------+-----------------------------+
SEE ALSO
eject(1), volcancel(1), volmissing(1) rmmount(1M), vold(1M), rmmount.conf(4), vold.conf(4), attributes(5), volfs(7FS)
WARNINGS
Due to a hardware limitation in many floppy drives, the act of checking for media causes mechanical action in the floppy drive. Continu-
ous polling of the floppy drive will cause the drive to wear out. It is recommended that polling the drive only be performed during periods
of high use.
SunOS 5.10 21 Feb 1997 volcheck(1)