10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
I have some scripts where I go and do some LDAP/NIS queries to report on users on Unix servers. What I am trying to figure out is, how do I know which server is the LDAP? The configs have been in place long before I took over so was hoping someone had some insight on how to figure this out. I must... (1 Reply)
Discussion started by: dagamier
1 Replies
2. AIX
Hello, I have an AIX6.1 machine which is a nim client to my nim master which is also AIX6.1 machine. I had some problem to perform an installation on my client using smit nim . i removed /etc/niminfo file in order to do the initialization again but when i run the command niminit -a name=client... (0 Replies)
Discussion started by: omonoiatis9
0 Replies
3. Red Hat
Goodmorning
i am preparing Nis for my test lab.Running Redhat 5.4 on master and centos for my client.Master server running portmap,ypserv,yppasswdd and client running portmap,ypbind and ypxfrd.
ypcat and other yp commands are running fine frm client.But when i try yppasswdd on client to change... (1 Reply)
Discussion started by: Vaibhav.T
1 Replies
4. Solaris
Hello - I have a Solaris machine, which I would like to configure as NIS master. When I run the command /usr/sbin/ypinit -m, I see below output. I am enclosing them in tags.
/usr/sbin/ypinit -m
In order for NIS to operate sucessfully, we have to construct a list of the
NIS servers. Please... (1 Reply)
Discussion started by: manju--
1 Replies
5. Solaris
Hi All,
In my network infra, there is a NIS master server and many more NIS slave servers. Now, I want every client to set with master server and one possible slave server so that if master goes down, client could still get info from slave server. The servers will be listed on... (0 Replies)
Discussion started by: naw_deepak
0 Replies
6. Solaris
Hi All,
I get below error while running
cd /var/yp
/usr/sbin/ypinit -m
Error Code - 1
updated netmasks
make : warning : target all not remade because of errors
current working dir /var/yp
*** error code 1 ***
make : fatal error : command failed for target 'k'
error running... (4 Replies)
Discussion started by: naw_deepak
4 Replies
7. Solaris
Hi, all.
I have a Solaris client here needs to bind to NIS server in another subnet. Following is the configuration i made on the client,
1) edit /etc/inet/hosts to add an entry of the NIS server -- nserver01
2) execute `domainname` to set local NIS domain to the domain of the NIS server.... (1 Reply)
Discussion started by: sn_wukong
1 Replies
8. UNIX for Advanced & Expert Users
I am running a DNS/NIS server on and older 2.6 system. I would like to move it to a newer system running Sol9. I have not found a good HOWTO and was looking for some advice.
Thanks in advance.
Dave (4 Replies)
Discussion started by: dlalonde
4 Replies
9. HP-UX
Hi all!
I am running an NIS Server with Linux. Now I want to configure a HPUX-Server to use this NIS Server. I have don all the configuration stuff exactly as described in the documentation.
When I run YPWHICH, it shows me the right server and domain. If I run YPCAT passwd, I'll get the... (4 Replies)
Discussion started by: pepade
4 Replies
10. UNIX for Advanced & Expert Users
Our NIS master server went down. We have since fixed it and brought it back up. However all of are machines still point to the slave server when looking at it with ypwhich. My question is how do i point the servers back to the master.
Frank (2 Replies)
Discussion started by: frankkahle
2 Replies