10 More Discussions You Might Find Interesting
1. Solaris
Hello,
I have an unloaded T5140 machine and want to access the ILOM for the first time and subsequently the network port after that., and then load Solaris 10 the final January 2011 build.
The first part is what confuses me -the cabling.
I am coming from a Windows machine (w/appropriate... (5 Replies)
Discussion started by: joboy
5 Replies
2. Solaris
Hi Everyone,
In my environment, I have few T5220. On the iLOM Management Card, I have both Network and Serial port are cabled, I don't have any issues while I try to connect using Network Management port, but when I try to connect the serial port for the same server which is actually connected... (3 Replies)
Discussion started by: bobby320
3 Replies
3. Shell Programming and Scripting
Hi,
I have a external board connected to my serial port. I need to execute "shutdown -r now" command when system boot up. When system boots up it requires a username ans password. Then I need to run my command. I can use rc script but that is rebooting system before it asks for username and... (0 Replies)
Discussion started by: charlie.arya
0 Replies
4. UNIX for Dummies Questions & Answers
A neighbour's Ubuntu 10.04 machine has five serial ports, one on the motherboard and four on a PCI card. However, only four cards are showing:
# dmesg | grep tty
console enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
... (2 Replies)
Discussion started by: dotancohen
2 Replies
5. Programming
i am having some coding problem in c for interfacing the GSM module through serial port. i want to send/receive sms. i have done all the setting for the port and know the AT command to use in this but i am actually having problem in reading and writing from serial port how to handle the signal when... (1 Reply)
Discussion started by: harsh_it
1 Replies
6. AIX
Hi,
How can i configure my modem in AIX thru serial port (sa0-->tty0)
I have two port serial card configured as sa0
I created tty1 which port is tty0 and which port is tty1 how can i know?? (1 Reply)
Discussion started by: pchangba
1 Replies
7. Programming
Hello!
Can someone advice me which method I will use if I want to communicate with device via RS232 serial port with this requirements:
1. Serial port is opened in non-canonical mode.
2. All the time I need to check is there something to read.
3. If I have to write something I need to write it... (6 Replies)
Discussion started by: jvrlic
6 Replies
8. Programming
I am developing an application in c with Linux OS, where a radio modem working at baud rate 9600 will be attached to PC on serial port. More than four such units will be communicating at one time, so there may be jamming or data corruption. Each module will be transmitting Data packets less than... (2 Replies)
Discussion started by: raj8109
2 Replies
9. Linux
Hi All,
I am a begineer in Linux, I have 4 ports and 3 are operational port 1,port 2 and port 4 (when I plug in serial device I can see it working) but port 3 seems it is not working.
I am sure the hardware is fine.
when I give command
dmesg | grep tty
I get,
serial 8250:ttyS0 at... (0 Replies)
Discussion started by: vr_82
0 Replies
10. SCO
Hi
I have just re-installed Compaq ML350 G2 Server with Unix SCO 5.0.5 and
informix DBMS .
on this server we have 2 serial ports , unfortunately its not working.
Can anyone help me to check the serial ports working or not OR guide me
to reconfigure it.
I have attached a device with... (1 Reply)
Discussion started by: munirh
1 Replies