10 More Discussions You Might Find Interesting
1. AIX
Hello,
On 4/20/2018, we performed a disk replacement on our IBM 8202 P7 server. After the disk was rebuilt, the SAS Disk Array sissas0 showed a status of degraded. However, the pdisks in the array all show a status of active.
We did see a message in errpt. DISK ARRAY PROTECTION SUSPENDED.
... (3 Replies)
Discussion started by: terrya
3 Replies
2. Filesystems, Disks and Memory
Hello,
On 4/20/2018, we performed a disk replacement on our IBM 8202 P7 server. After the disk was rebuilt, the SAS Disk Array sissas0 showed a status of degraded. However, the pdisks in the array all show a status of active.
We did see a message in errpt. DISK ARRAY PROTECTION SUSPENDED.
... (1 Reply)
Discussion started by: terrya
1 Replies
3. AIX
Hi,
One of my disk is in 'disk missing state'. It is a sharedVG and cluster nodes.
The errpt keeps reporting stale partition error.
lvs are in open/stale state.
In this sceanario is replacing the disk the best practice?
When i do a lsdev the disk is labelled as below.
hdisk3 Available ... (2 Replies)
Discussion started by: ElizabethPJ
2 Replies
4. HP-UX
Hello,
I'm new to this forum and as you will see from my question I'm new to UNIX as well.
One of our costumers has HP rx4640 running on UNIX with two 300GB hot-swappable disks that are mirrored. They reported to us that one of the disks is faulty and they want us to take care of it. Below is... (16 Replies)
Discussion started by: gjk
16 Replies
5. Solaris
Hello,
I have a Sparc system with encapsulated disks.
Because of disk errors I had to replace rootdisk,
I did it with
vxdiskadm 4)
replacement, vxdctl disable/enable,
vxdiskadm 5)
After it it the system boot failed, dropped back to the ok> prompt, message was:
The file... (0 Replies)
Discussion started by: ggi
0 Replies
6. Linux
Hi all,
I'm kind of new to programming in Linux & c/c++. I'm currently writing a FileManager using Ubuntu Linux(10.10) for Learning Purposes. I've got started on this project by creating a loopback device to be used as my virtual hard disk. After creating the loop back hard disk and mounting it... (23 Replies)
Discussion started by: shen747
23 Replies
7. Shell Programming and Scripting
Hello,
I have the following perl array:
@longname = (Fasthernet0/0 Fasthernet0/1 Serial0/1/0 Serial0/2/1 Tunnel55 Tunnel77)
with the followinh array:
@shortname = (Fa0/0 Fa0/1 Se0/1/0 Se0/2/1 Tu55 Tu77)
in other words, I need to remove the following from each element in the array... (4 Replies)
Discussion started by: ahmed_zaher
4 Replies
8. Solaris
Hello,
Can someone advise the proper procedure for replacing a mirrored disk in SVM. I have checked the docs and various websites but the procedure seems to vary. This is what I would do...
1. Remove the db replicas from the bad disk.
2. Detach it from the mirror
3. Clear it with... (4 Replies)
Discussion started by: Actuator
4 Replies
9. Red Hat
Hi all,
I need some help with a RHEL 4 on a Sun Fire v65x machine.
Some of the disks is damaged or has a hardware issue. This disk is connected to a hardware raid.
The problem is that I don't know what is the brand, model and capacity of the disk.
I've read the raid manual, but says... (3 Replies)
Discussion started by: adelgadom
3 Replies
10. Solaris
I dont even know what raid level this is, but its raid 5 mirrored from the looks of it.
I have a failed disk (t12) within this mirror. What is the best way to replace this disk? 2 things concern me, isn't there a command to prepare the disk for a hot swap? and what should i do with the... (3 Replies)
Discussion started by: BG_JrAdmin
3 Replies
vxreattach(1M) vxreattach(1M)
NAME
vxreattach - reattach disk drives that have once again become accessible
SYNOPSIS
/etc/vx/bin/vxreattach [-br ] [accessname...]
/etc/vx/bin/vxreattach -c accessname
DESCRIPTION
The vxreattach utility reattaches disks to the disk group they were in and retains the same media name.
This operation may be necessary if a disk has a transient failure, or if Veritas Volume Manager (VxVM) starts with some disk drivers
unloaded and unloadable. Disks then enter the failed state. If the problem is fixed, vxreattach may be able to reattach the disks without
plexes being flagged as stale, as long as the reattach happens before any volumes on the disk are started.
vxreattach tries to find a disk in the same disk group with the same disk ID for the disk(s) to be reattached. The reattach operation may
fail even after finding the disk with the matching disk ID if the original cause (or some other cause) for the disk failure still exists.
vxreattach is usually invoked by vxdiskadm when performing disk recovery. It is not intended to be run directly by an administrator.
OPTIONS
-b Performs the reattach operation in the background.
-c Checks if a reattach is possible. No operation is performed, but the name of the disk group and disk media name at which the
disk can be reattached is displayed.
-r Tries to recover stale plexes of any volumes on the failed disk. It does this by calling vxrecover.
EXIT CODES
A zero exit status is returned if the reattach is performed; non-zero is returned otherwise.
See vxintro(1M) for a list of standard exit codes.
EXAMPLES
Check if reattachment of disk c1t2d0 is possible:
/etc/vx/bin/vxreattach -c c1t2d0
If reattachment is possible, vxreattach returns with an exit status of 0 and displays the disk group name and disk media name. If reat-
tachment is not possible, vxreattach returns an exit status of 2 and displays an error.
Attempt to reattach the disk in the foreground and try to recover stale plexes of any volumes on the disk:
/etc/vx/bin/vxreattach -r c1t2d0
If the reattachment is successful, vxreattach returns an exit status of 0. Otherwise, if an error occurs, vxreattach returns a non-zero
exit code as defined on vxintro(1M).
FILES
/etc/default/vxplex Standard defaults file that can be used to determine whether FastResync is used when attaching plexes. See vxplex(1M)
for details.
SEE ALSO
vxdiskadm(1M), vxintro(1M), vxplex(1M), vxrecover(1M)
VxVM 5.0.31.1 24 Mar 2008 vxreattach(1M)
