8 More Discussions You Might Find Interesting
1. Solaris
I have installed Solaris 11 Express on my machine. On my GA-X58A-UD5 motherboard there are two 6 Gb/s SATA ports (Marvell 9128 chip), but when I connect a hard drive to one of them, the system does not recognize it.
However, when I boot from a USB install image (downloaded from here Oracle... (1 Reply)
Discussion started by: RychnD
1 Replies
2. Hardware
I have an upgrade path in mind for a new computer that will be stocked with a 2TB SATA 300 hard disk. This is a choice based on information that SATA 300 is not necessarily faster than SATA 600. The upgrade path in a year time or so would then involve the purchase of an SSD that would contain the... (4 Replies)
Discussion started by: figaro
4 Replies
3. Hardware
Hello everybody,
I need to connect a laptop 2.5 SATA hard drive to a Desktop board (which uses 3.5' SATA hard drives). I've tried the connectors and they fit excellent in the 2.5 SATA connectors.
The problem is that the laptop hard drive uses 5v and the PC's power source sends 12v. So, my... (4 Replies)
Discussion started by: Zykl0n-B
4 Replies
4. UNIX for Advanced & Expert Users
trying to setup a sata drive using a sata to scsi adaptor
I have a sata 1TB Deskstar that I had setup before and during shipment from a facilty to another, the disk failed. The handling was not great, lots of throwing boxes, etc. I have a new disk from Hitachi (thankyou Hitachi) anyway, I don't... (1 Reply)
Discussion started by: mndavies
1 Replies
5. UNIX for Advanced & Expert Users
Hi,
I have two sata hard-disks. Out of those, one is having RHEL5 operating system, and other is having fedora7 operating system.
When I connect the disk with RHEL5 operating system to sata0 port and disk with fedora7 operating system to sata1 port. While booting it shows RHEL5 boot screen,... (3 Replies)
Discussion started by: praveen_b744
3 Replies
6. Shell Programming and Scripting
hi
how floppy disks, CDs and flash drives (pen drives) are accessed in UNIX?
thanks (0 Replies)
Discussion started by: nokia1100
0 Replies
7. UNIX for Advanced & Expert Users
i have a system which has two hard disks..one is sata and the other one is normal ata hard disk.
i wish to install red hat enterprise linux WS(desktop edition) on my sata hard disk..but the installer shows me only my ata hard disk..
i searched the net..it says that a library-- libata will let it... (2 Replies)
Discussion started by: ankit.jss
2 Replies
8. Solaris
can any one help me look for a driver for SATA harddisk, im installing solaris 9 to it.
thanks and regards
msouthofheavenk ;) (2 Replies)
Discussion started by: msouthofheavenk
2 Replies
SMARTCTL(8) System Manager's Manual SMARTCTL(8)
NAME
smartctl - S.M.A.R.T. control utility
SYNOPSIS
smartctl [-cdeglostv] [device]
DESCRIPTION
smartctl controls the Self-Monitoring, Analysis and Reporting Technology System(S.M.A.R.T.) built into ATA-3 and later IDE and SCSI-3 Hard
Drives. This is used to check the reliability of the hard drive and predict drive failures. TapeAlerts support for SCSI tape drives and
changers smartctl is command line utility designed to perform simple S.M.A.R.T. tasks.
OPTIONS
smartctl accepts two agruments, options and device in respective order. The options begin with a '-' and multiple options should be begun
with a single '-'. The second argument is the device to be controled. ATA device use the form "/dev/hd*" and SCSI devices use the form
"/dev/sd*". SCSI devices use only options a,i,c,e,d. For SCSI Tape Drives and Changers with TapeAlerts support use the form "/dev/st*" and
"/dev/sg*". TapeAlerts devices use only a,i,c,e,d.
i Check if the device supports S.M.A.R.T
c Check if device has any S.M.A.R.T. Warranty Failures
g Prints only the generic S.M.A.R.T. attributes
v Prints only the vendor specific S.M.A.R.T. attributes
t Prints only the vendor specific S.M.A.R.T. thresholds
l Prints only the S.M.A.R.T. error log
a Prints all parameters for c,i,g,v,t,l (for SCSI c,i)
e Enables S.M.A.R.T. on device
d Disables S.M.A.R.T. on device
t Enables S.M.A.R.T. automatic offline self test timer which scans the drive every four hours for disk defects.
T Disables S.M.A.R.T. automatic offline self test timer
O Runs S.M.A.R.T. Immediate off-line Test
S Runs S.M.A.R.T. Short Self Test ( usually under ten minutes)
s Runs S.M.A.R.T. Short Self Test in Captive Mode.
( WARNING: This test will busy out drive for length of test. Only run this on drives without any mounted partitions.)
X Runs S.M.A.R.T. Extended Self Test ( tens of minutes)
x Runs S.M.A.R.T. Extended Self Test in Captive Mode. ( WARNING: This test will busy out drive for length of test. Only run this on
drives without any mounted partitions.)
A Aborts Non-Captive S.M.A.R.T. Tests.
EXAMPLES
smartctl -a /dev/hda - prints all S.M.A.R.T. infomration for drive /dev/hda (Primary Master)
smartctl -d /dev/hdd - disable S.M.A.R.T. on drive /dev/hdd (Secondary Slave)
AUTHOR
Michael Cornwell, cornwell@acm.org
Concurrent Systems Laboratory
Jack Baskin School of Engineering
University of California Santa Cruz
http://csl.cse.ucsc.edu/
smartctl-2.1 September 13, 2001 SMARTCTL(8)