9 More Discussions You Might Find Interesting
1. Linux
I bought for backup this controller
LSI LSI9212-4i4e 6G SAS
I will buy a quantum reader like this
Quantum TC-L62BN-EM 2500GB LTO
Two simple question
a)I read..2500GB,this mean i cannot use tape lto6 over 3tb?
b)Wich external cable?A sata external cable is good?
Thanks (0 Replies)
Discussion started by: Linusolaradm1
0 Replies
2. UNIX for Dummies Questions & Answers
How is sas related to web development - once we have the sas code executed what is the necessity to create a html output??
Any sas and html users welcome .. (2 Replies)
Discussion started by: swathi123
2 Replies
3. UNIX for Dummies Questions & Answers
HI all,
I am very new to AIX (matter of fact Unix). We are currently automating out manual process using Unix Shell Scripting.
My wrote a shell script which will accept the name of the sas job as parameter, checks the existense of the sas file in the specified folder.
If it is not present,... (1 Reply)
Discussion started by: anubhav2020
1 Replies
4. UNIX Desktop Questions & Answers
I'm not sure if anyone can help here. I don't know much about Unix but will give the information that I can.
I am trying to run audits of my data with the command sas audit. When it asks for a batch number I put in the number that I am looking to print.
When I do this I am getting the... (1 Reply)
Discussion started by: jld1124
1 Replies
5. Solaris
Hi, I have a solaris box with an LSI SAS HBA and a16 bay SAS JBOD. I can only see 15 of the 16 drives, ID 7 is not seen. Do I have to edit the st.conf file to get things to work properly?
Thanks (0 Replies)
Discussion started by: montanye
0 Replies
6. UNIX for Advanced & Expert Users
Does anyone had perfomed a tuning with SAS on Solaris???
Performance is not so good and I found out that Share Memory an Semaphores are the same that initial instalation, I havent found info at internet
Please help (1 Reply)
Discussion started by: alex blanco
1 Replies
7. Shell Programming and Scripting
hi
how floppy disks, CDs and flash drives (pen drives) are accessed in UNIX?
thanks (0 Replies)
Discussion started by: nokia1100
0 Replies
8. Shell Programming and Scripting
Hi,
I am executing the SAS program using Unix script to call SAS program, but i would like to run that SAS program in forground mode, does anyone know what is command.
Thanks in advance!! (0 Replies)
Discussion started by: terala
0 Replies
9. Shell Programming and Scripting
I need some help on sas on unix....
Is there any way to validate date in sas (1 Reply)
Discussion started by: radhika03
1 Replies
MFI(4) BSD Kernel Interfaces Manual MFI(4)
NAME
mfi -- LSI MegaRAID SAS driver
SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file:
device pci
device mfi
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
mfi_load="YES"
DESCRIPTION
This driver is for LSI's next generation PCI Express SAS RAID controllers. Access to RAID arrays (logical disks) from this driver is pro-
vided via /dev/mfid? device nodes. A simple management interface is also provided on a per-controller basis via the /dev/mfi? device node.
The mfi name is derived from the phrase "MegaRAID Firmware Interface", which is substantially different than the old "MegaRAID" interface and
thus requires a new driver. Older SCSI and SATA MegaRAID cards are supported by amr(4) and will not work with this driver.
Two sysctls are provided to tune the mfi driver's behavior when a request is made to remove a mounted volume. By default the driver will
disallow any requests to remove a mounted volume. If the sysctl dev.mfi.%d.delete_busy_volumes is set to 1, then the driver will allow
mounted volumes to be removed.
HARDWARE
The mfi driver supports the following hardware:
o LSI MegaRAID SAS 1078
o LSI MegaRAID SAS 8408E
o LSI MegaRAID SAS 8480E
o LSI MegaRAID SAS 9260
o Dell PERC5
o Dell PERC6
o IBM ServeRAID M5015 SAS/SATA
o IBM ServeRAID-MR10i
o Intel RAID Controller SROMBSAS18E
FILES
/dev/mfid? array/logical disk interface
/dev/mfi? management interface
DIAGNOSTICS
mfid%d: Unable to delete busy device An attempt was made to remove a mounted volume.
SEE ALSO
amr(4), pci(4), mfiutil(8)
HISTORY
The mfi driver first appeared in FreeBSD 6.1.
AUTHORS
The mfi driver and this manual page were written by Scott Long <scottl@FreeBSD.org>.
BUGS
The driver does not support big-endian architectures at this time.
BSD
May 12, 2010 BSD