9 More Discussions You Might Find Interesting
1. Linux
I bought for backup this controller
LSI LSI9212-4i4e 6G SAS
I will buy a quantum reader like this
Quantum TC-L62BN-EM 2500GB LTO
Two simple question
a)I read..2500GB,this mean i cannot use tape lto6 over 3tb?
b)Wich external cable?A sata external cable is good?
Thanks (0 Replies)
Discussion started by: Linusolaradm1
0 Replies
2. UNIX for Dummies Questions & Answers
How is sas related to web development - once we have the sas code executed what is the necessity to create a html output??
Any sas and html users welcome .. (2 Replies)
Discussion started by: swathi123
2 Replies
3. UNIX for Dummies Questions & Answers
HI all,
I am very new to AIX (matter of fact Unix). We are currently automating out manual process using Unix Shell Scripting.
My wrote a shell script which will accept the name of the sas job as parameter, checks the existense of the sas file in the specified folder.
If it is not present,... (1 Reply)
Discussion started by: anubhav2020
1 Replies
4. UNIX Desktop Questions & Answers
I'm not sure if anyone can help here. I don't know much about Unix but will give the information that I can.
I am trying to run audits of my data with the command sas audit. When it asks for a batch number I put in the number that I am looking to print.
When I do this I am getting the... (1 Reply)
Discussion started by: jld1124
1 Replies
5. Solaris
Hi, I have a solaris box with an LSI SAS HBA and a16 bay SAS JBOD. I can only see 15 of the 16 drives, ID 7 is not seen. Do I have to edit the st.conf file to get things to work properly?
Thanks (0 Replies)
Discussion started by: montanye
0 Replies
6. UNIX for Advanced & Expert Users
Does anyone had perfomed a tuning with SAS on Solaris???
Performance is not so good and I found out that Share Memory an Semaphores are the same that initial instalation, I havent found info at internet
Please help (1 Reply)
Discussion started by: alex blanco
1 Replies
7. Shell Programming and Scripting
hi
how floppy disks, CDs and flash drives (pen drives) are accessed in UNIX?
thanks (0 Replies)
Discussion started by: nokia1100
0 Replies
8. Shell Programming and Scripting
Hi,
I am executing the SAS program using Unix script to call SAS program, but i would like to run that SAS program in forground mode, does anyone know what is command.
Thanks in advance!! (0 Replies)
Discussion started by: terala
0 Replies
9. Shell Programming and Scripting
I need some help on sas on unix....
Is there any way to validate date in sas (1 Reply)
Discussion started by: radhika03
1 Replies
TWS(4) BSD Kernel Interfaces Manual TWS(4)
NAME
tws -- 3ware 9750 SATA+SAS 6Gb/s RAID controller card driver
SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file:
device scbus
device tws
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
tws_load="YES"
DESCRIPTION
The tws driver provides support for LSI's 3ware 9750 SATA+SAS 6Gb/s RAID controller cards.
These controllers feature the LSISAS2108 6Gb/s SAS RAID-on-Chip (ROC) and are available in 4- and 8-port configurations, supports RAID levels
0, 1, 5, 6, 10, 50 and single disk, with 96 SATA and/or SAS hard drives and SSDs.
For further hardware information, see http://www.lsi.com/.
HARDWARE
The tws driver supports the following SATA/SAS RAID controller:
o LSI's 3ware SAS 9750 series
LOADER TUNABLES
Tunables can be set at the loader(8) prompt before booting the kernel or stored in loader.conf(5).
hw.tws.cam_depth The maximum queued CAM SIM requests for one controller. The default value is 256.
hw.tws.enable_msi This tunable enables MSI support on the controller if set to a non-zero value. The default value is 0.
hw.tws.queue_depth The maximum queued requests for one controller.
hw.tws.use_32bit_sgls Limit the driver to use only 32-bit SG elements regardless whether the operating system is running in 64-bit mode.
The default value is 0.
FILES
/dev/da? array/logical disk interface
/dev/tws? management interface
DIAGNOSTICS
Whenever the driver encounters a command failure, it prints out an error code in the format: "ERROR: (<error source>: <error code>):", fol-
lowed by a text description of the error. There are other error messages and warnings that the driver prints out, depending on the kinds of
errors that it encounters. If the driver is compiled with TWS_DEBUG defined, it prints out a whole bunch of debug messages.
SEE ALSO
da(4), scsi(4)
AUTHORS
The tws driver was written by Manjunath Ranganathaiah for LSI and this manual page was written by Xin LI <delphij@FreeBSD.org> for iXsystems,
Inc.
BSD
October 4, 2011 BSD