Removed crashed node from Solaris Cluster 3.0


 
Thread Tools Search this Thread
Special Forums UNIX and Linux Applications High Performance Computing Removed crashed node from Solaris Cluster 3.0
# 1  
Old 08-12-2008
Removed crashed node from Solaris Cluster 3.0

All-

I am new to these forums so please excuse me if this post is in the wrong place.

I had a node crash in a 4 node cluster and mgmt has determined this node will not be part of the cluster when rebuilt. I am researching how to remove it from the cluster information on the other 3 nodes and have found procedures to do this for a node that is part of a cluster.

I am looking for steps to remove the references to the crashed node from the cluster configuration on the other 3 nodes.

All 4 system are the same:

v880
Sol 8
Sun Cluster 3.0
Veritas VM 3.2

Any assistance is greatly appreciated in advance!
# 2  
Old 08-13-2008
Did you try the procedure given in 6.2 Adding and Removing a Cluster Node (Sun Cluster 3.0 U1 System Administration Guide) - Sun Microsystems ?

If so, what problems did you see?

Tim
---
# 3  
Old 08-14-2008
Tim-

That procedure assume that node it`s still up and participating in the cluster. The node I describe is down (powered off now) and will not join the cluster again.

Can I start at step 4 of How to Put a Node Into Maintenance State and continue?

Thanks in Advance!
Login or Register to Ask a Question

Previous Thread | Next Thread

10 More Discussions You Might Find Interesting

1. AIX

Cluster node not starting

Setting up HACMP 6.1 on a two node cluster. The other node works fine and can start properly on STABLE state (VGs varied, FS mounted, Service IP aliased). However, the other node is always stuck on ST_JOINING state. Its taking forever and you can't stop the cluster as well or recover from script... (2 Replies)
Discussion started by: depam
2 Replies

2. Solaris

SVM metaset on 2 node Solaris cluster storage replicated to non-clustered Solaris node

Hi, Is it possible to have a Solaris cluster of 2 nodes at SITE-A using SVM and creating metaset using say 2 LUNs (on SAN). Then replicating these 2 LUNs to remote site SITE-B via storage based replication and then using these LUNs by importing them as a metaset on a server at SITE-B which is... (0 Replies)
Discussion started by: dn2011
0 Replies

3. AIX

How to add node to the cluster with stoping the application?

In the production hacmp 5.3 is running with three nodes but i want to add new node to cluster with out stopping the application ie with same resource group if any bady know pls help me. (1 Reply)
Discussion started by: manjunath.m
1 Replies

4. Solaris

How to remove single node cluster

Hi Gurus, I am very new to clustering and for test i have created a single node cluster, now i want to remove the system from cluster. Did some googling however as a newbee in cluster unable to co related the info. Please help Thanks (1 Reply)
Discussion started by: kumarmani
1 Replies

5. HP-UX

Identify cluster active node

Hello, Is there any way to identify the active node in a HP-UX cluster without root privileges? (3 Replies)
Discussion started by: psimoes79
3 Replies

6. Solaris

Active Sun cluster node?

I now the logical name and Virtual IP of the cluster. How can I find the active sun cluster node without having root access? (3 Replies)
Discussion started by: sreeniatbp
3 Replies

7. High Performance Computing

Setting up 2 node cluster using solaris 10

hi, i am trying to setup a 2 node cluster environment. following is what i have; 1. 2 x sun ultra60 - 450MHz procs, 1GB RAM, 9GB HDD, solaris 10 2. 2 x HBA cards 3. 2 x Connection leads to connect ultra60 with D1000 4. 1 x D1000 storage box. 5. 3 x 9GB HDD + 2 x 36GB HDD first of all,... (1 Reply)
Discussion started by: solman17
1 Replies

8. HP-UX

MC/SG Fail to join cluster node

Hi, Please advise me whereas I have two node cluster server configured with MC/SG. Application and DB are running on Node 1, while Node 2 is standby. All the volume group devices are part of cluster environment. There is only one package running at node 1. Node 2 is having the problem to... (1 Reply)
Discussion started by: rauphelhunter
1 Replies

9. HP-UX

Node can't join cluster

Need help guys! when running cmrunnode batch i'm getting this error cmrunnode : Waiting for cluster to... (1 Reply)
Discussion started by: Tris
1 Replies

10. Shell Programming and Scripting

The other node name of a SUN cluster

Hello, Under ksh I have to run a script on one of the nodes of a Solaris 8 cluster which at some time must execute a command on the alternate node: # rsh <name> "command" I have to implement this script on all the clusters of my company (a lot of...). Fortunately, the names of the two nodes... (11 Replies)
Discussion started by: heartwork
11 Replies
Login or Register to Ask a Question