7 More Discussions You Might Find Interesting
1. What is on Your Mind?
Got a raise and a formal position of 'unix system engineer' in 2016.
I would like to thank you members and admins.
This would not be possible without you.
I will mention some..
Thank you Don, for making me learn and understand the importance of standards, which i try to apply as much as i... (3 Replies)
Discussion started by: Peasant
3 Replies
2. Solaris
Hello experts -
I am planning to install a Sun cluster 4.0 zone cluster fail-over. few basic doubts.
(1) Where should i install the cluster s/w binaries ?. ( global zone or the container zone where i am planning to install the zone fail-over)
(2) Or should i perform the installation on... (0 Replies)
Discussion started by: NVA
0 Replies
3. Solaris
Yesterday my customer told me to expect a vcs upgrade to happen in the future. He also plans to stop using HDS and move to EMC.
Am thinking how to migrate to sun cluster setup instead.
My plan as follows leave the existing vcs intact as a fallback plan.
Then install and build suncluster on... (5 Replies)
Discussion started by: sparcguy
5 Replies
4. Linux
Hi all,
I am new to Linux.Can anyone tell me how to display or list all the members in a group?
Thanks in advance. (9 Replies)
Discussion started by: arthi
9 Replies
5. High Performance Computing
Dear All,
Can anyone explain about Pros and Cons of SUN and Veritas Cluster ?
Any comparison chart is highly appreciated.
Regards,
RAA (4 Replies)
Discussion started by: RAA
4 Replies
6. High Performance Computing
Provides a description of how to set up a Solaris Cluster Express cluster in a VirtualBox on OpenSolaris.
More... (0 Replies)
Discussion started by: Linux Bot
0 Replies
7. Post Here to Contact Site Administrators and Moderators
The Members Only Forum sub-heading has a spelling mistake. It should read visible. (1 Reply)
Discussion started by: dangral
1 Replies
LEARN ABOUT OPENSOLARIS
clsetup
clsetup(1CL) Sun Cluster Maintenance Commands clsetup(1CL)
NAME
clsetup - configure Sun Cluster interactively
SYNOPSIS
/usr/cluster/bin/clsetup -V
/usr/cluster/bin/clsetup -?
/usr/cluster/bin/clsetup [-f logfile]
DESCRIPTION
The clsetup command provides the following configuration capabilities, depending on what state the cluster is in when you issue the com-
mand. The user must be superuser to run this command.
This command has no short form.
o When you run the clsetup command at post-installation time, the command performs initial setup tasks, such as configuring quorum
devices and resetting the installmode property. If you deselected automatic Quroum Configuration when you created the cluster
using either scinstall or the cluster create command, then you must run the clsetup command immediately after the cluster has
been installed. Ensure that all nodes have joined the cluster before you run the clsetup command and reset the installmode prop-
erty.
If you used automatic quorum configuration when you created the cluster, you do not need to run the clsetup command after clus-
ter installation. The automatic quorum configuration feature also resets the installmode property of the cluster.
You can issue this form of the clsetup command from any node in the cluster.
o When you run the clsetup command during normal cluster operation, the scsetup command provides an interactive, menu-driven util-
ity to perform cluster configuration tasks. The following are some of the cluster components which this utility administers:
o Quorum
o Resource groups
o Data services
o Cluster interconnect
o Device groups and volumes
o Private hostnames
o New nodes
o Other cluster properties
You can issue this form of the clsetup command from any node in the cluster.
o When you run the clsetup command from a node that is in noncluster mode, the clsetup command provides a menu-driven utility for
changing and displaying the private IP address range.
You must reboot all nodes into noncluster mode before you start this form of the clsetup utility.
OPTIONS
The following options are supported:
-?
--help
Prints help information for the command.
-f logfile
--file logfile
Specifies the name of a log file to which commands can be logged. If this option is specified, most command sets generated by clsetup
can br run and logged, or just logged, depending on user responses.
-V
--version
Prints the version of the command set. No command line processing will be performed and the command will not enter into its interactive
menu.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWsczu |
+-----------------------------+-----------------------------+
|Interface Stability |Evolving |
+-----------------------------+-----------------------------+
SEE ALSO
Intro(1CL), cldevicegroup(1CL), clnode(1CL), clquorum(1CL), clreslogicalhostname(1CL), clresourcegroup(1CL), clresourcetype(1CL),
clressharedaddress(1CL), cluster(1CL), cltelemetryattribute(1CL)
Sun Cluster 3.2 5 May 2006 clsetup(1CL)
