10 More Discussions You Might Find Interesting
1. AIX
Hi,
We had a hardware problem with an IBM System p5 server, with AIX 5.2
We restore from a tape the last backup we had, but the server does not boot up as expected.
The server try to mount some directories from a storage, but could not comunicate with them, we check the FC and everything is... (12 Replies)
Discussion started by: trevian3969
12 Replies
2. HP-UX
I am trying to reload a RP4440 with 2x300gb disks and dual Port Network card, with HPUX 11.11 Sept 2003. When the os boots and and gets to the main menu to install HPUX or run recovery, it cannot find the disks or NIC.
At the OS prompt (after loading files), ioscan shows the Class ba, and shows... (0 Replies)
Discussion started by: mrmurdock
0 Replies
3. SCO
OK group, it's been 12 years since I worked with SCO. I need some direction here:
SCO Openserver 5.07
I have a server with a bad motherboard. I have moved the SCSI adapter and hard drive to another computer. This new server has different hardware so I must install the chipset drivers for... (1 Reply)
Discussion started by: jscholz
1 Replies
4. SCO
I inserted a PCI Realtek RTL8139 network adapter on a PC running SCO Openserver 5.0.6.
I successfully loaded drivers and I'm trying to install the card with netconfig command, unfortunately without success.
Here are the steps I follow to install the card:
I run netconfig, from menu 'hardware'... (2 Replies)
Discussion started by: kampus
2 Replies
5. HP-UX
Hi ,
Hi what is an adapter?what is its use ?
How to log into a tibco server from unix home directory. (1 Reply)
Discussion started by: megh
1 Replies
6. AIX
I have 1 PCI-X Dual Channel Ultra320 SCSI Adapter card for my p570 server. I would like to split the 2 channels for the usage of 2 tape drives in different LPARs. Is that possible?
For example, I have 2 LPARs running in p570 server, LPAR-A configured the Ultra320 card as pci7 in slot... (11 Replies)
Discussion started by: kwliew999
11 Replies
7. Solaris
Okay. I admit I'm sort of a newbie in this regard.
I installed a SCSI adapter on a Sun Ultra 5 workstation. I did the standard STOP-A on the startup and got the OK prompt. I then tried probe-scsi-all. It dumps me back @ the OK prompt w/ no message whatsoever. I tried probe-scsi, nothing.
... (3 Replies)
Discussion started by: Plain Person
3 Replies
8. Solaris
Hi. I need to find a simple SCSI adapter card for a Sun Ultra 5 workstation. I don't need the type w/ ethernet attached (e.g. X1032) as I already have ethernet onboard & they are more spendy.
I know Adaptec is out, but what unit would work? I am attaching an external SCSI tape unit to this... (4 Replies)
Discussion started by: Plain Person
4 Replies
9. IP Networking
Im newest in unix,
Please, give me solution for installing lan adapter if driver not found in the list of ethernet drivers
ihave unix driver in a dos diskete
please give me the other solution
and tell me where the domain of unix class online, so ican read from it.
Thank's very much (3 Replies)
Discussion started by: ade_muhdiat
3 Replies
10. UNIX for Dummies Questions & Answers
Can anyone out there help me out? I'm trying to install a scsi tape back up on a sys running sco openserver 5.0.4. When I go through the steps for mkdev tape it seems like it works, but when I reboot I still don't see the tape. Also when it boots up I get a scsi bios not installed error. I've... (1 Reply)
Discussion started by: goatboy_tx
1 Replies
adpu320(7D) Devices adpu320(7D)
NAME
adpu320 - Adaptec Ultra320 SCSI host bus adapter driver
SYNOPSIS
scsi@unit-address
DESCRIPTION
The adpu320 host bus adapter driver is a SCSA-compliant nexus driver that supports the following Adaptec Ultra320 SCSI Devices:
Chips AIC-7902
The adpu320 driver supports standard functions provided by the SCSA interface, including tagged and untagged queuing, Wide/Fast/Ultra SCSI,
and auto request sense. The adpu320 driver does not support linked commands. The adpu320 driver supports hot swap SCSI and hot plug PCI.
Additionally, the adpu320 driver supports the following features:
o 64-bit addressing (Dual address Cycle)
o PCI-X v1.1 operating up to 133MHz and 64bits
o PCI bus spec v2.2 operating up to 66MHz and 64bits
o Packetized SCSI at 320 and 160 MB/s
o QAS
o DT
o 40MB/sec in single-ended mode and up to 320MB/sec transfer rate in LVD mode
o Domain Validation
o Retained Training Information (RTI)
o PCI and PCI-X Error handling
Driver Configuration
The adpu320 host bus adapter driver is configured by defining the properties found in adpu320.conf. Properties in the adpu320.conf file
that can be modified by the user include: ADPU320_SCSI_RD_STRM, ADPU320_SCSI_NLUN_SUPPORT.
-------------------------------------------------------------
Option: ADPU320_SCSI_RD_STRM=[value]
Definition: Enables/disables read streaming negotiation
for all drives.
Possible Values: 0 (off), 1 (on)
Default Value: 0 (off)
Option: ADPU320_SCSI_NLUN_SUPPORT=[value]
Definition: Enables the number of logical units to be
scanned per drive.
Possible Values: 1-64
Default Value: 64
-------------------------------------------------------------
If you alter or add driver parameters incorrectly, you can render your system inoperable. Use driver parameters with caution.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |x86 |
+-----------------------------+-----------------------------+
FILES
/kernel/drv/adpu320
driver module
/kernel/drv/amd64/adpu320
64-bit driver module
/kernel/drv/adpu320.conf
configuration file
/boot/solaris/drivers/notisa.010/adpu320.bef
realmode driver
SEE ALSO
cfgadm(1M), prtconf(1M), attributes(5), scsi_abort(9F), scsi_hba_attach(9F), scsi_ifgetcap(9F), scsi_reset(9F), scsi_sync_pkt(9F),
scsi_transport(9F), scsi_device(9S), scsi_extended_sense(9S), scsi_inquiry(9S), scsi_pkt(9S)
Writing Device Drivers
Small Computer System Interface-3 (SCSI-3)
SunOS 5.10 19 Oct 2004 adpu320(7D)
