10 More Discussions You Might Find Interesting
1. AIX
Hi,
We had a hardware problem with an IBM System p5 server, with AIX 5.2
We restore from a tape the last backup we had, but the server does not boot up as expected.
The server try to mount some directories from a storage, but could not comunicate with them, we check the FC and everything is... (12 Replies)
Discussion started by: trevian3969
12 Replies
2. HP-UX
I am trying to reload a RP4440 with 2x300gb disks and dual Port Network card, with HPUX 11.11 Sept 2003. When the os boots and and gets to the main menu to install HPUX or run recovery, it cannot find the disks or NIC.
At the OS prompt (after loading files), ioscan shows the Class ba, and shows... (0 Replies)
Discussion started by: mrmurdock
0 Replies
3. SCO
OK group, it's been 12 years since I worked with SCO. I need some direction here:
SCO Openserver 5.07
I have a server with a bad motherboard. I have moved the SCSI adapter and hard drive to another computer. This new server has different hardware so I must install the chipset drivers for... (1 Reply)
Discussion started by: jscholz
1 Replies
4. SCO
I inserted a PCI Realtek RTL8139 network adapter on a PC running SCO Openserver 5.0.6.
I successfully loaded drivers and I'm trying to install the card with netconfig command, unfortunately without success.
Here are the steps I follow to install the card:
I run netconfig, from menu 'hardware'... (2 Replies)
Discussion started by: kampus
2 Replies
5. HP-UX
Hi ,
Hi what is an adapter?what is its use ?
How to log into a tibco server from unix home directory. (1 Reply)
Discussion started by: megh
1 Replies
6. AIX
I have 1 PCI-X Dual Channel Ultra320 SCSI Adapter card for my p570 server. I would like to split the 2 channels for the usage of 2 tape drives in different LPARs. Is that possible?
For example, I have 2 LPARs running in p570 server, LPAR-A configured the Ultra320 card as pci7 in slot... (11 Replies)
Discussion started by: kwliew999
11 Replies
7. Solaris
Okay. I admit I'm sort of a newbie in this regard.
I installed a SCSI adapter on a Sun Ultra 5 workstation. I did the standard STOP-A on the startup and got the OK prompt. I then tried probe-scsi-all. It dumps me back @ the OK prompt w/ no message whatsoever. I tried probe-scsi, nothing.
... (3 Replies)
Discussion started by: Plain Person
3 Replies
8. Solaris
Hi. I need to find a simple SCSI adapter card for a Sun Ultra 5 workstation. I don't need the type w/ ethernet attached (e.g. X1032) as I already have ethernet onboard & they are more spendy.
I know Adaptec is out, but what unit would work? I am attaching an external SCSI tape unit to this... (4 Replies)
Discussion started by: Plain Person
4 Replies
9. IP Networking
Im newest in unix,
Please, give me solution for installing lan adapter if driver not found in the list of ethernet drivers
ihave unix driver in a dos diskete
please give me the other solution
and tell me where the domain of unix class online, so ican read from it.
Thank's very much (3 Replies)
Discussion started by: ade_muhdiat
3 Replies
10. UNIX for Dummies Questions & Answers
Can anyone out there help me out? I'm trying to install a scsi tape back up on a sys running sco openserver 5.0.4. When I go through the steps for mkdev tape it seems like it works, but when I reboot I still don't see the tape. Also when it boots up I get a scsi bios not installed error. I've... (1 Reply)
Discussion started by: goatboy_tx
1 Replies
AHD(4) BSD Kernel Interfaces Manual AHD(4)
NAME
ahd -- Adaptec PCI/PCI-X Ultra320 SCSI host adapter driver
SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file:
device pci
device scbus
device ahd
To compile in debugging code:
options AHD_DEBUG
options AHD_DEBUG_OPTS=<bitmask of options>
options AHD_REG_PRETTY_PRINT
To configure one or more controllers to assume the target role:
options AHD_TMODE_ENABLE=<bitmask of units>
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
ahd_load="YES"
DESCRIPTION
This driver provides access to the SCSI bus(es) connected to Adaptec AIC79xx host adapter chips.
Driver features include support for narrow and wide busses, fast, ultra, ultra2, ultra160, and ultra320 synchronous transfers, packetized
transfers, tagged queueing, 512 SCB's, and target mode.
The AHD_DEBUG_OPTS option is used to control which diagnostic messages are printed to the console when AHD_DEBUG is enabled. Logically OR
the following bits together:
Value Function
0x0001 Show miscellaneous information
0x0002 Show sense data
0x0004 Show Serial EEPROM contents
0x0008 Show bus termination settings
0x0010 Show host memory usage
0x0020 Show SCSI protocol messages
0x0040 Show mode pointer of the chip register window
0x0080 Show selection timeouts
0x0100 Show FIFO usage messages
0x0200 Show Queue Full status
0x0400 Show SCB queue status
0x0800 Show inbound packet information
0x1000 Show S/G list information
0x2000 Enable extra diagnostic code in the firmware
The AHD_REG_PRETTY_PRINT option compiles in support for human-readable bit definitions for each register that is printed by the debugging
code. However, it also bloats the compiled size of the driver by approximately 215KB.
Individual controllers may be configured to operate in the target role through the AHD_TMODE_ENABLE configuration option. The value assigned
to this option should be a bitmap of all units where target mode is desired. For example, a value of 0x25 would enable target mode on units
0, 2, and 5. Note that target mode is only supported for ultra160 speeds and below.
Per target configuration performed in the SCSI-Select menu, accessible at boot, is honored by this driver. This includes synchronous/asyn-
chronous transfers, maximum synchronous negotiation rate, wide transfers, disconnection, and the host adapter's SCSI ID.
HARDWARE
The ahd driver supports the following:
o Adaptec AIC7901 host adapter chip
o Adaptec AIC7901A host adapter chip
o Adaptec AIC7902 host adapter chip
o Adaptec 29320 host adapter
o Adaptec 39320 host adapter
o Many motherboards with on-board SCSI support
SEE ALSO
ahc(4), cd(4), da(4), sa(4), scsi(4)
HISTORY
The ahd driver first appeared in FreeBSD 4.7.
AUTHORS
The ahd driver, the AIC7xxx sequencer-code assembler, and the firmware running on the aic79xx chips was written by Justin T. Gibbs. This
manual page is based on the ahc(4) manual page.
BUGS
The current generation of 79xx chips do not support target mode in Ultra320 mode. Target mode in general has not been well tested in this
driver.
BSD
July 4, 2004 BSD