10 More Discussions You Might Find Interesting
1. Solaris
Hi all,
this time I'd need a help from an advanced Solaris system admin :rolleyes:
I attached a HP StorageWorks Ultrium 215 Tape Drives - Overview - c00059530 - HP Business Support Center to my Sun E220R and it got recognized immediately (probe-scsi-all).
Now the operating system boot process... (8 Replies)
Discussion started by: pseudocoder
8 Replies
2. UNIX for Dummies Questions & Answers
Currenty running SCO Openserver 6 at a Dell PowerEdge T300. I recently installed a driver for an Adaptec SCSI card (adpu320). When I connect a tape drive to it and re-start the system,it freezes and displays the following message: "WARNING: adpu320: Command timed out (ha= 4)" and the system... (2 Replies)
Discussion started by: RicardoM
2 Replies
3. AIX
Dear all,
I have ultriam3 tape. It is connected my LPAR. I have that the Sl.Nos. and slot number. but run the cfmgr i am not getting the tape drive.
I have fired the command lsdev -Cc tape but no reply.
how will i configure the tape in LPAR?
Please suggest. It is very urgent. (3 Replies)
Discussion started by: pernasivam
3 Replies
4. SCO
I replaced a HP Superstore Dat 40 with another HP Superstore Dat 40, but my backupedge software keeps putting up error code 1 (device not found) I have tried reinstaling the drive as DAT Alad stp 0 6 0 0. I'm not a computer expert but willing to have a go. I went into Backupedge to try and format a... (2 Replies)
Discussion started by: James Zwecker
2 Replies
5. SCO
Hello,
I'm having some issues with installing SCSI tape drive on SCO 5.0.6
hardware config shows the following adapters
%adapter 0xE800-0xE8FF 10 - type=alad ha=0 bus=0 id=7 fts=sto
%adapter 0x0170-0x0177 15 - type=IDE ctlr=secondary dvr=wd
%adapter - 3 - ... (3 Replies)
Discussion started by: ananth_ak
3 Replies
6. Solaris
I will be honest I am quite new to UNIX and Solaris so this may be a simple thing.
I have just purchased a Sun (rebranded HP obviously) DAT DDS3 SCSI tape drive for my Sun Ultra 10 running Solaris 10.
I have previously fitted a SCSI card to the box which has configured ok and can be seen from... (1 Reply)
Discussion started by: mattw
1 Replies
7. Solaris
hi-
I just installed a quad gigaswift ethernet scsi card to my sunblade 150. I checked with the docs, and got all of the required drivers on the box. Now, I'm trying to mount an external scsi tape drive with no luck. I set the scsi address on the external drive to 0. Here's what I'm coming... (9 Replies)
Discussion started by: ECBROWN
9 Replies
8. Filesystems, Disks and Memory
Hi all, please help I am stuck.
I have installed a external unipack scsi tape drive. The tape drive is Exabyte Eliant 820. All I did was connected scsi cable and power it on. When issued "probe-scsi-all" command, the tape is correctly identified. However, when issued "dmesg | more" command, the... (4 Replies)
Discussion started by: dennis
4 Replies
9. Filesystems, Disks and Memory
I'm researching a tape drive + backup software to work across my unix/linux network. Was thinking about a dds4 tape drive (sony's) on my solaris ultra2, with some kind of software that would work across the network to back up my other 2 solaris boxes, plus my 2 linux boxes. What do others use... (3 Replies)
Discussion started by: kymberm
3 Replies
10. UNIX for Dummies Questions & Answers
I'm running SCO OS 505 on a Compaq proliant 1600, and my tape drive will just not work. It was working properly and whent to Sh?ts when I tried to get the cd rom working. I have uninstalled any configured tape drive and rebooted and then configured a tape drive and rebooted still nothing. I'm... (4 Replies)
Discussion started by: kikkin
4 Replies
tz(4) Kernel Interfaces Manual tz(4)
Name
tz - SCSI magnetic tape interface
Syntax
VAX NCR 5380:
adapter uba0 at nexus?
controller scsi0 at uba0 csr 0x200c0080 vector szintr
tape tz0 at scsi0 drive 0
VAX DEC SII:
adapter ibus0 at nexus?
controller sii0 at ibus? vector sii_intr
tape tz0 at sii0 drive 0
RISC DEC SII:
adapter ibus0 at nexus?
controller sii0 at ibus? vector sii_intr
tape tz0 at sii0 drive 0
RISC DEC KZQ:
adapter uba0 at nexus?
controller kzq0 at ibus? csr 0761300vector sii_intr
tape tz0 at kzq0 drive 0
RISC NCR ASC:
adapter ibus0 at nexus?
controller asc0 at ibus? vector ascintr
tape tz0 at asc0 drive 0
Description
The SCSI tape driver provides a standard tape drive interface as described in This is a driver for any Digital SCSI tape device.
For the TZK10 QIC format tape drive, the densities supported are QIC-24 (read only) block size of 512 byte blocks, QIC-120, and QIC-150
read/write block size of 512 byte blocks, and QIC-320 read/write block size of 1024 byte blocks. With QIC format style tapes all reads and
writes must be in multiple of the block size. This is a requirement of fixed block tape drives because record boundaries are not pre-
served. The QIC densities are selected using the following special device names:
QIC-24 Fixed block size.
QIC-120 Fixed block size.
QIC-150 Fixed block size.
QIC-320 Fixed block size.
With all fixed block tape devices a of a file to the tape must be padded out. An example of this is a of which has a size of approximately
3800 bytes.
dd if=/etc/gettytab of=/dev/rmt0h bs=10k conv=sync
or
dd if=/etc/gettytab of=/dev/rmt0l bs=512 conv=sync
The option of pads the output to block size.
This driver also supports n-buffered reads and writes to the raw tape interface (used with streaming tape drives). See for further
details.
Tape Support
TZ30, TZK50, TLZ04, TSZ05, TKZ08, TZK10
Diagnostics
All diagnostic messages are sent to the error logger subsystem.
Files
See Also
mtio(4), nbuf(4), SCSI(4), MAKEDEV(8), uerf(8), tapex(8)
Guide to the Error Logger
tz(4)
