10 More Discussions You Might Find Interesting
1. Hardware
Hi gurus,
I am trying make wireless card working but I am stuck. Tried following:
Hardware button for wifi is enabled (wifi led lights):
# modprobe -r iwl3945
# modprobe iwl3945
# ifconfig wlan0 up
SIOCSIFFLAGS: No such device
# ifup wlan0
/sbin/ifup: configuration for wlan0 not... (2 Replies)
Discussion started by: wakatana
2 Replies
2. Hardware
Hi gurus, I am experiencing strange networks problems. I am trying to teather internet from HTC Desire S with Android. Basicly I followed those instructions: https://wiki.archlinux.org/index.php/Android_Tethering#Procedure
1.) Enable USB Debugging - Phone: Settings --> Applications -->... (0 Replies)
Discussion started by: wakatana
0 Replies
3. HP-UX
Hello all,
I hope someone can help me.
We have Compaq Tru64 UNIX V5.1B (Rev. 2650).
By latest Belarus government act Europe/Minsk timezone was changed to
GMT+3 without DST (was GMT+2 with DST).
Please advice how to do changes on our machine.
Thank You in advance,
md1982 (15 Replies)
Discussion started by: md1982
15 Replies
4. Windows & DOS: Issues & Discussions
Hi all,
Laptop compaq presario v3000 is not booting! It just gives 3 beeps and there is no display. All the green LEDs are glowing!
I have "performed a hard reset" as per HP site
Troubleshooting Black Screen Displays with No Error Messages During Startup or Boot Compaq Presario V3115AU... (7 Replies)
Discussion started by: ./hari.sh
7 Replies
5. Linux
Hi,
Trying to install a small OS to run this old laptop.
Compaq Presario 1685, circa '98
Processor: AMD K6-2 380 MHz Data Bus Speed: 66 MHz
Ram Installed 32 MB moduled
Hard Drive: 4.3 GB
DVD-ROM
Burned in a CD “PUPPY-4.3beta1-k2.6.25.16-v423-SCSI”, tried to boot with it several times BUT... (7 Replies)
Discussion started by: nichos
7 Replies
6. SuSE
Any one try this. I am getting errors or it just hangs up. I have tried redhat, suse,ubuntu etc but nothing will load.
When i try to boot the live cd they boot up OK but then just hang after a while and the cd rom stop spinning etc.
Just wondering if anyone has use this hdw and what linux... (2 Replies)
Discussion started by: admaix
2 Replies
7. SCO
i want to install sco unix 5.0.5 on compaq presario laptop c773tu dual boot with windos xp.
the HDD is 160 GB
RAM 2046 MB ddr2.
I have created partitions and loaded Win XP
While installing SCO Unix 5.0.5 i get the following problem
1)memory excessively fragmented. I get around it by sepcifying... (0 Replies)
Discussion started by: vikramviky
0 Replies
8. UNIX for Dummies Questions & Answers
Hi,
I am new to UNIX. I need help in working with Compaq-UX TRU64 OS.
How It work FTP Server?
ANd MAil Server?
and I have apach pprogram project and it work as HTTP Server.
Also I need how can setup a new version of progrm on UNix like mozilla and adobe reader etc...........
Thank... (3 Replies)
Discussion started by: svuad
3 Replies
9. SCO
Trying to install Sco openserver on HP Proliant with this scsi controller but no scsi devices detected.
Boot controller is set as the smart array 532 but SCSI diags do not detect any SCSI boot devices during boot sequence
Any help appreciated (2 Replies)
Discussion started by: farmacy
2 Replies
10. Programming
Hi All
Following is the lines of code which simply makes a structure of 1 bit member and 7 bit is unused.Then the structure is initialised with char pointer.The output on HPUX(BIG Endian) and Compaq(Little Endian) are different.On HPUX it gives zero and Compaq it gives 1. I never thought that the... (7 Replies)
Discussion started by: Shobhit
7 Replies
TL(4) BSD Kernel Interfaces Manual TL(4)
NAME
tl -- Texas Instruments ThunderLAN Ethernet device driver
SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file:
device miibus
device tl
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
if_tl_load="YES"
DESCRIPTION
The tl driver provides support for PCI Ethernet adapters based on the Texas Instruments ThunderLAN Ethernet controller chip.
The ThunderLAN controller has a standard MII interface that supports up to 32 physical interface devices (PHYs). It also has a built-in
10baseT PHY hardwired at MII address 31, which may be used in some 10Mbps-only hardware configurations. In 100Mbps configurations, a
National Semiconductor DP83840A or other MII-compliant PHY may be attached to the ThunderLAN's MII bus. If a DP83840A or equivalent is
available, the ThunderLAN chip can operate at either 100Mbps or 10Mbps in either half-duplex or full-duplex modes. The ThunderLAN's built-in
PHY and the DP83840A also support autonegotiation.
The tl driver supports the following media types:
autoselect Enable autoselection of the media type and options. Note that this option is only available on those PHYs that support
autonegotiation. Also, the PHY will not advertise those modes that have been explicitly disabled using the following
media options.
10baseT/UTP Set 10Mbps operation
100baseTX Set 100Mbps (Fast Ethernet) operation
10base5/AUI Enable AUI/BNC interface (useful only with the built-in PHY).
The tl driver supports the following media options:
full-duplex Force full duplex operation
half-duplex Force half duplex operation.
hw-loopback Enable hardware loopback mode.
Note that the 100baseTX media type is only available if supported by the PHY. For more information on configuring this device, see
ifconfig(8).
HARDWARE
The tl driver supports Texas Instruments ThunderLAN based Ethernet and Fast Ethernet adapters including a large number of Compaq PCI Ethernet
adapters. Also supported are:
o Olicom OC-2135/2138 10/100 TX UTP adapter
o Olicom OC-2325/OC-2326 10/100 TX UTP adapter
o Racore 8148 10baseT/100baseTX/100baseFX adapter
o Racore 8165 10/100baseTX adapter
The tl driver also supports the built-in Ethernet adapters of various Compaq Prosignia servers and Compaq Deskpro desktop machines including:
o Compaq Netelligent 10
o Compaq Netelligent 10 T PCI UTP/Coax
o Compaq Netelligent 10/100
o Compaq Netelligent 10/100 Dual-Port
o Compaq Netelligent 10/100 Proliant
o Compaq Netelligent 10/100 TX Embedded UTP
o Compaq Netelligent 10/100 TX UTP
o Compaq NetFlex 3P
o Compaq NetFlex 3P Integrated
o Compaq NetFlex 3P w/BNC
DIAGNOSTICS
tl%d: couldn't map memory A fatal initialization error has occurred.
tl%d: couldn't map interrupt A fatal initialization error has occurred.
tl%d: device timeout The device has stopped responding to the network, or there is a problem with the network connection (cable).
tl%d: no memory for rx list The driver failed to allocate an mbuf for the receiver ring.
tl%d: no memory for tx list The driver failed to allocate an mbuf for the transmitter ring when allocating a pad buffer or collapsing an
mbuf chain into a cluster.
SEE ALSO
arp(4), miibus(4), netintro(4), ng_ether(4), ifconfig(8)
HISTORY
The tl device driver first appeared in FreeBSD 2.2.
AUTHORS
The tl driver was written by Bill Paul <wpaul@ctr.columbia.edu>.
BSD July 16, 2005 BSD