10 More Discussions You Might Find Interesting
1. SCO
I need to be able to make a backup image of an OLD UNIX server HD where I can restore the complete HD from scratch if (when) the HD fails. This server runs the accounting system for a company.
I can and have backed the data up via local FTP, but O/S and Apps are so old that I am not sure I could... (21 Replies)
Discussion started by: chrishouse
21 Replies
2. Hardware
We have a 3ware RAID server at work, and as the appointed systems administrator (by virtue of being the one with the most knowledge) I've taken on the job of maintaining it. I've installed smartmontools on it to keep an eye on the drives and run scans every day, and looking at the data from the... (0 Replies)
Discussion started by: Krendoshazin
0 Replies
3. Debian
I am installing a Debian Server on a:
HP Proliant DL380 G4
Dual CPU's 3.20 ghz / 800 mhz / 1MB L2
5120 MB RAM
6 hard disks on HP Smart Array 6i controller (36.4 GB Ultra320 SCSI HD each)
I will be using this server to capture VHS video, encode, compress, cut, edit, make DVD's, rip... (0 Replies)
Discussion started by: Marcus Aurelius
0 Replies
4. AIX
Hello,
I have a scsi pci x raid controller card on which I had created a disk array of 3 disks
when I type lspv ; I used to see 3 physical disks ( two local disks and one raid 5 disk )
suddenly the raid 5 disk array disappeared ; so the hardware engineer thought the problem was with SCSI... (0 Replies)
Discussion started by: filosophizer
0 Replies
5. Linux
I just built a home computer with 3TB hard drives I wanted to set up in a RAID 5 and load Ubuntu server onto it.
The first thing I did was set up the drives in a RAID 5 using just the motherboard chipset software to do it, so a 'hardware' RAID basically.
I installed Windows first to see if... (2 Replies)
Discussion started by: lorewap3
2 Replies
6. Hardware
Hi guys.
if we want to use SSD drives on a database server, can we use RAID 0 configuration because of their reliability? (3 Replies)
Discussion started by: majid.merkava
3 Replies
7. Hardware
Hi All
I have a Sun T2000 server. Couple of years ago I had configured and mirrored the boot drive with an other drive using hardware RAID 1 using raidctl command.
Following is the hardware RAID output.
root@oracledatabaseserver / $ raidctl
RAID Volume RAID RAID Disk... (0 Replies)
Discussion started by: Tirmazi
0 Replies
8. UNIX for Dummies Questions & Answers
I need to put together a RAID1 file server for use by Windoze systems. I've built zillions of windows systems from components. I was a HPUX SE for a long time at HP, but have been out of the game for years.
I've got an old workhorse mobo FIC PA-2013 with a 450 MHz K6 III+ I could use, but I'd... (2 Replies)
Discussion started by: pcmacd
2 Replies
9. Red Hat
I am planning on building a fedora box with raid controller (database server).
Is anybody done that ? also what kind of software do you need to backup and recover data. (1 Reply)
Discussion started by: amir07
1 Replies
10. Filesystems, Disks and Memory
Help, if possible.
In SCO Open Server with installation of two-channel RAID controller the following happens: on the channel 0 disk array is seen by an operational system, and on the channel 1 array is not seen (simultaneously). That is the operational system can not simultaneously use more than... (1 Reply)
Discussion started by: pko60
1 Replies
RAIDFILE-CONFIG(8) Box Backup RAIDFILE-CONFIG(8)
NAME
raidfile-config - Configure Box Backup's RAID files
SYNOPSIS
raidfile-config config-dir blocksize dir1 [dir2 [dir3]]
DESCRIPTION
raidfile-config creates a raidfile.conf file for Box Backup. This file holds information about the directories used to store backups in.
Box Backup supports userland RAID, in a restricted RAID5 configuration, where 3 and only 3 'drives' are supported. You can read more about
RAID5 (and other RAID-levels) here[1].
Parameters
The parameters are as follows:
config-dir
The directory path where configuration files are located. Usually this is /etc/box. raidfile.conf will be written in this directory.
blocksize
The block size used for file storage in the system, in bytes. Using a multiple of the file system block size is a good strategy.
Depending on the size of the files you will be backing up, this multiple varies. Of course it also depends on the native block size of
your file system.
dir1
The first directory in the built-in RAID array.
dir2
The second directory in the built-in RAID array. If you are not using the built-in RAID functionality, this field should be ignored.
You should not use the built-in RAID if you have a hardware RAID solution or if you're using another type of software RAID (like md on
Linux).
dir3
The third directory in the built-in RAID array. The same notes that apply to dir2 also apply to dir3.
Note that there are currently no way to add multiple disk sets to the raidfile.conf file using command line tools, etc. See
raidfile.conf(5) for details on adding more disks.
BUGS
If you find a bug in Box Backup, and you want to let us know about it, join the mailing list[2], and send a description of the problem
there.
To report a bug, give us at least the following information:
o The version of Box Backup you are running
o The platform you are running on (hardware and OS), for both client and server.
o If possible attach your config files (bbstored.conf, bbackupd.conf) to the bug report.
o Also attach any log file output that helps shed light on the problem you are seeing.
o And last but certainly not least, a description of what you are seeing, in as much detail as possible.
FILES
raidfile-config generates the raidfile.conf(5) file.
SEE ALSO
bbstored-config(8), bbstored.conf(5), raidfile.conf(5)
AUTHORS
Ben Summers
Per Thomsen
James O'Gorman
NOTES
1. here
http://en.wikipedia.org/wiki/Redundant_array_of_independent_disks#RAID_5
2. mailing list
http://lists.warhead.org.uk/mailman/listinfo/boxbackup
Box Backup 0.11 10/28/2011 RAIDFILE-CONFIG(8)
