9 More Discussions You Might Find Interesting
1. AIX
Hi Experts, Kind of embarrassed to ask this , it's been a while I've done this . Can anyone verify below procedure to replace HBA in the VIO server. Many client LPARs are using this HBA for NPIV . Please correct me if I am wrong . Thanks in Advanced
Identify the HBA (did that)
Unconfigure the... (2 Replies)
Discussion started by: JME2015
2 Replies
2. AIX
Thanks I need to know if my server has dual HBA and if multipath has been configured. For Multipath I ran lspath and it shows all drives and if MPIO is configured for that drive.
Thanks for any input. (2 Replies)
Discussion started by: 300zxmuro
2 Replies
3. AIX
Hi,
I want to know whether IBM AIX can be installed on the IBM e series and x series server hardware?
Thanks & Regards
Arun (2 Replies)
Discussion started by: Arun.Kakarla
2 Replies
4. Hardware
We've inherited some IBM Infoprint 6400 printers for use with our internal warehouse management software. Now I'm looking for a driver, or a compatibility list for said printers. I found that IBM does provide drivers for it (link), but due to our policies I can't download it. (who provides drivers... (0 Replies)
Discussion started by: pludi
0 Replies
5. UNIX for Advanced & Expert Users
hello, i have a dell Poweredge 2950 ( Server ) and an IBM storage device DS 3000 family ( Storage ) . I am supposed to link the IBM storage device to the Dell Poweredge via "Emulex 4Gb Fibre Channel Host Bus Adapter".
I have put the addapter card in my server and connected it to the storage.... (3 Replies)
Discussion started by: nux007
3 Replies
6. HP-UX
We have an old k class server that we would like to use as a testbed for our oracle application. However, it is not booting properly - fiailing the self boot test (light at the back of server is blinking). On the little window on the front of server i see the following message about console (?). ... (9 Replies)
Discussion started by: lombard_c
9 Replies
7. HP-UX
Hi friends
i dont know whether it is the right forum to ask this or not. if its not please excuse me and please give me the link for such a forum.
i am novice about HP 9000 rp3410 server and its things but i had to install and configure it. I came to know that it doesnot comes with builtin... (4 Replies)
Discussion started by: bnaravinda
4 Replies
8. UNIX for Dummies Questions & Answers
Hi all,
I'm trying to find out info on HP 9000 rp7420 server.
16-way rp7420 server - what does 16-way stand for?
There is 32-way rpxxxx also.
I searched www.hp.com site but no luck.
Can anyone put some light in it pls.
Thanks in advance (3 Replies)
Discussion started by: mhbd
3 Replies
9. HP-UX
I work for a school and just received a set of HP-UX machines. I did ok with the Vizualize workstations in that they had video cards and all, but I am attempting to set up the D Class (D250) servers that we received and they are terminal only. I have the terminals and keyboards for them, but am... (11 Replies)
Discussion started by: NoHope
11 Replies
DPM-MODIFYFS(1) DPM Administrator Commands DPM-MODIFYFS(1)
NAME
dpm-modifyfs - modify the parameters of a disk pool filesystem
SYNOPSIS
dpm-modifyfs --server fs_server --fs fs_name [ --st status ] [ --weight weight ] [ --help ]
DESCRIPTION
dpm-modifyfs modifies the parameters of a disk pool filesystem.
This command requires ADMIN privilege.
OPTIONS
server specifies the host name of the disk server where this filesystem is mounted.
fs specifies the mount point of the dedicated filesystem.
status New status of this filesystem. It can be set to 0 (enabled read/write) or DISABLED or RDONLY. This can be either alphanumeric or
the corresponding numeric value.
weight specifies the weight of the filesystem. This is used during the filesystem selection. The value must be positive. It is recommended
to use a value lower than 10.
EXAMPLE
dpm-modifyfs --server sehost --fs /data --st RDONLY
EXIT STATUS
This program returns 0 if the operation was successful or >0 if the operation failed.
SEE ALSO
dpm(1), dpm_modifyfs(3)
LCG
$Date$ DPM-MODIFYFS(1)