10 More Discussions You Might Find Interesting
1. AIX
Hello,
On 4/20/2018, we performed a disk replacement on our IBM 8202 P7 server. After the disk was rebuilt, the SAS Disk Array sissas0 showed a status of degraded. However, the pdisks in the array all show a status of active.
We did see a message in errpt. DISK ARRAY PROTECTION SUSPENDED.
... (3 Replies)
Discussion started by: terrya
3 Replies
2. AIX
Hi,
One of my disk is in 'disk missing state'. It is a sharedVG and cluster nodes.
The errpt keeps reporting stale partition error.
lvs are in open/stale state.
In this sceanario is replacing the disk the best practice?
When i do a lsdev the disk is labelled as below.
hdisk3 Available ... (2 Replies)
Discussion started by: ElizabethPJ
2 Replies
3. HP-UX
Hello,
I'm new to this forum and as you will see from my question I'm new to UNIX as well.
One of our costumers has HP rx4640 running on UNIX with two 300GB hot-swappable disks that are mirrored. They reported to us that one of the disks is faulty and they want us to take care of it. Below is... (16 Replies)
Discussion started by: gjk
16 Replies
4. Solaris
Hello,
I have a Sparc system with encapsulated disks.
Because of disk errors I had to replace rootdisk,
I did it with
vxdiskadm 4)
replacement, vxdctl disable/enable,
vxdiskadm 5)
After it it the system boot failed, dropped back to the ok> prompt, message was:
The file... (0 Replies)
Discussion started by: ggi
0 Replies
5. AIX
Hi,
The system is a Power6 8204 with an external storage 7031. OS is AIX 5.3. I replaced a failed disk hdisk28 and put it back to the volume group. Everything looks just fine. After the replacement, errpt has kept sending "Perm DISK OPERATION ERROR".
Other than the error, everything still... (1 Reply)
Discussion started by: aixlover
1 Replies
6. HP-UX
hi all!
I found a the state of disk at JA0/D13 was failed this morning.
then i replaced it this afternoon,but i run
#dsp -s
the array status displayed
====================================
STATUS
Subsystem State: 1
The Subsystem is TESTING.
The array is REBUILDING and is 87%... (0 Replies)
Discussion started by: JoyOnLine
0 Replies
7. Solaris
Hello,
Can someone advise the proper procedure for replacing a mirrored disk in SVM. I have checked the docs and various websites but the procedure seems to vary. This is what I would do...
1. Remove the db replicas from the bad disk.
2. Detach it from the mirror
3. Clear it with... (4 Replies)
Discussion started by: Actuator
4 Replies
8. Red Hat
Hi all,
I need some help with a RHEL 4 on a Sun Fire v65x machine.
Some of the disks is damaged or has a hardware issue. This disk is connected to a hardware raid.
The problem is that I don't know what is the brand, model and capacity of the disk.
I've read the raid manual, but says... (3 Replies)
Discussion started by: adelgadom
3 Replies
9. Solaris
I dont even know what raid level this is, but its raid 5 mirrored from the looks of it.
I have a failed disk (t12) within this mirror. What is the best way to replace this disk? 2 things concern me, isn't there a command to prepare the disk for a hot swap? and what should i do with the... (3 Replies)
Discussion started by: BG_JrAdmin
3 Replies
10. UNIX for Dummies Questions & Answers
I have just started getting into unix and aquired a Sun Ultra 5 however the disk failed and I want to replace it with a spare maxtor 40Gb i have lying around. I need to partition and format the disk from its old windows format. I have looked up info on the format command in solaris 9 and I think i... (2 Replies)
Discussion started by: kalm
2 Replies
