10 More Discussions You Might Find Interesting
1. Red Hat
Hi,
I would like to know scsi id of hard drive, which command is used to find scsi id of hard drive and disk related information.
Regards
Manoj (3 Replies)
Discussion started by: manoj.solaris
3 Replies
2. Ubuntu
Hi
I have dual operating system i.e Win XP and KUBUNTU. Now my windows XP is corrupted and i want to reinstall Win XP. So i just want to know Shall i have to reinstall Linux also or i can only reinstall win xp without affecting linux installation.
Thanks
Sarbjit (3 Replies)
Discussion started by: sarbjit
3 Replies
3. UNIX for Dummies Questions & Answers
i hava bought scsi card for taking backup in a 12/24 DAT DRIVE -scounix5.05 i am havaing the cd of the same contain driver files how should i install it. can anybody help me. (0 Replies)
Discussion started by: tatacoffee
0 Replies
4. SCO
Hello,
I'm having some issues with installing SCSI tape drive on SCO 5.0.6
hardware config shows the following adapters
%adapter 0xE800-0xE8FF 10 - type=alad ha=0 bus=0 id=7 fts=sto
%adapter 0x0170-0x0177 15 - type=IDE ctlr=secondary dvr=wd
%adapter - 3 - ... (3 Replies)
Discussion started by: ananth_ak
3 Replies
5. Linux
Hi all,
I wanted to install the latest version of firefox 2 but it seems when I attempt to install it, it seems to be saying it is looking for c libraries version 2.3? I believe I currently have an older version of the c libraries. I am currently running Sun's JDS Linux 2003. My Mozilla web... (1 Reply)
Discussion started by: scriptingmani
1 Replies
6. Solaris
Okay. I admit I'm sort of a newbie in this regard.
I installed a SCSI adapter on a Sun Ultra 5 workstation. I did the standard STOP-A on the startup and got the OK prompt. I then tried probe-scsi-all. It dumps me back @ the OK prompt w/ no message whatsoever. I tried probe-scsi, nothing.
... (3 Replies)
Discussion started by: Plain Person
3 Replies
7. UNIX for Advanced & Expert Users
I would like to install a AIT drive to the scsi connector on our solaris box. I am very new to the unix world and would be greatful if someone could help or lead me in the right direction.
Thanks (4 Replies)
Discussion started by: vpyle
4 Replies
8. UNIX for Dummies Questions & Answers
Hi,
I have installed a SCSI Controller onto an HPUX 10.20b and I don't have any driver files for it when I check in Sys Admin. Do I need to update the kernel? I am not sure how to get the computer to recognize this controller... any suggestions?
Thanks (2 Replies)
Discussion started by: nattie_h
2 Replies
9. Filesystems, Disks and Memory
Hi all, please help I am stuck.
I have installed a external unipack scsi tape drive. The tape drive is Exabyte Eliant 820. All I did was connected scsi cable and power it on. When issued "probe-scsi-all" command, the tape is correctly identified. However, when issued "dmesg | more" command, the... (4 Replies)
Discussion started by: dennis
4 Replies
10. UNIX for Advanced & Expert Users
How can you get a scsi card to initalize or decome available at boot up on AIX 4.3 (1 Reply)
Discussion started by: truma1
1 Replies
UK(4) BSD Kernel Interfaces Manual UK(4)
NAME
uk -- SCSI user-level driver
SYNOPSIS
uk* at scsibus? target ? lun ?
DESCRIPTION
The uk driver provides support for a process to address devices on the SCSI bus for which there is no configured driver.
A SCSI adapter must also be separately configured into the system before this driver makes sense.
KERNEL CONFIGURATION
If a count is given, that number of uk devices will be configured into the NetBSD kernel.
IOCTLS
The uk driver has no ioctls of its own but rather acts as a medium for the generic scsi(4) ioctls. These are described in <sys/scsiio.h>.
FILES
/dev/uk[0-255] unknown SCSI devices.
DIAGNOSTICS
All scsi(4) debug ioctls work on uk devices.
SEE ALSO
ioctl(2), cd(4), ch(4), scsi(4), sd(4), ss(4), st(4)
HISTORY
The uk driver appeared in 386BSD 0.1.
BSD
October 11, 1993 BSD
