Netfilter conntracking for P2P protocols (edonkey, bittorent...)

10 More Discussions You Might Find Interesting

1. Cybersecurity

How to use Netfilter properly with IPv6?

Hello, on a PC with Debian 8 I try to use a Bash script with Netfilter rules so that only traffic goes in and out that is wanted. For that I set all 3 default policies to "drop". The machine uses DHCP to get its IP, gateway and DNS. And I never checked so I was quite surprised that my...

2. AIX

How to disable insecure protocols?

Hello all, planning to secure AIX sever by disabling insecure protocols/cipher suites; got the below requirements from secuirty team. 1.configure the server to disable support for DES and IDEA cipher suites 2.disable insecure TLS/SSL protocol support Configure the server to...

3. IP Networking

what are L2,L3 protocols.

hello forum members, What are L2 and L3 Protocols and can u brief me a bit little ie to gain a basic knowledge. Thanks & Regards Rajkumar g

4. Linux

netfilter / iptables

HI, Is the Netfilter and IPtables same? Thanks & Regards Arun

5. IP Networking

p2p

OK Guys I need help. I'm interest in P2p , can you recommend some books or sites about it thx in advance

6. UNIX for Dummies Questions & Answers

Intranet P2P Filesharing

I need suggestions for what to use. I need all my users to be able to share files and be able to search into all their files. I also need to control how much bandwidth they use so my network doesn't overload. I can't have my users searching/downloading directly from each other which is my...

7. IP Networking

define IP protocols on network

what method would I use to determine which IP protocols network

8. Programming

Help in extending netfilter

Hi everybody, I have to write a module for matching in netfilter , extending the netfilter but I'm facing some problems can somebody guide me in that. I know that I need to write matching module working in kernel space and a program in userspace. I went through the HOWTO on netfilter-hacking but...

9. UNIX for Dummies Questions & Answers

Protocols

What protocol would be the best to use on a network with nt and unix servers and windows me clients? Can SMB protocol be used to implement large networks? What protocol can be used to make remote file systems appear as if they are local? Quite a few questions I know, any help would be...

10. UNIX for Dummies Questions & Answers

network protocols

Which network protocol is used by UNIX systems to make remote file systems appear as if they are local?

LEARN ABOUT DEBIAN

gnunet-nat-server

GNUNET-NAT-SERVER(1)					      General Commands Manual					      GNUNET-NAT-SERVER(1)

NAME

       gnunet-nat-server - help GNUnet setup test network setup with NAT

SYNOPSIS

       gnunet-nat-server [options] PORT

DESCRIPTION

       Normal  GNUnet end-users should not concern themselves with gnunet-nat-server.  In fact, distributions are encouraged to consider not ship-
       ping it at all.	Running gnunet-nat-server's is similar to running hostlist servers: it is a special service to the community with  special
       requirements and no benefit to those running the service.

       This  program  will listen on the specified PORT for incoming requests to test a peer's network connectivity.  Incoming requests can ask it
       to connect to a given IPv4 address (and port) using TCP or UDP and to send a 2-byte test message using the specified address.  The  program
       can  also  be asked to send a "fake" ICMP response message to a given IPv4 address (for autonomous NAT traversal --- see the description in
       the respective research paper).

       The idea is that gnunet-nat-server will be run on some trusted hosts with unrestricted connectivity to allow GNUnet  users  to  test  their
       network	configuration.	 As  written, the code allows any user on the Internet to cause the gnunet-nat-server to send 2-bytes of arbitrary
       data to any TCP or UDP port at any address.  We believe that this is generally harmless.

       When running gnunet-nat-server, make sure to use a configuration that disables most NAT options but enables  'enable_nat_client'  and  sets
       'internal_address'  to  the  global  IP address of your local host.  Also, the gnunet-helper-nat-client should be installed locally and run
       with root privileges (SUID), otherwise the gnunet-nat-server will not work properly.

       Note that gnunet-nat-server could be run via gnunet-arm but typically is not.  Also, the name of the host and port  that  gnunet-nat-server
       is  run on should be specified in the NATSERVER option in the [setup] section of the configuration file of hosts that are supposed to auto-
       configure with this server.

OPTIONS

       -c FILENAME,  --config=FILENAME
	      Use the configuration file FILENAME.

BUGS

       Report bugs by using Mantis <https://gnunet.org/bugs/> or by sending electronic mail to <gnunet-developers@gnu.org>

SEE ALSO

       gnunet-transport(1)

GNUnet								    25 Feb 2012 					      GNUNET-NAT-SERVER(1)

Cybersecurity