10 More Discussions You Might Find Interesting
1. UNIX for Beginners Questions & Answers
Dear friends
I use RedHat 6.5, which sets the gateway in the configuration file / etc / sysconfig / network as GATEWAY = 192.168.1.26, and the gateway in the configuration file / etc / sysconfig / network-scripts / ifcfg-eth11 as GATEWAY = 192.168.1.256. The two gateways are different.... (6 Replies)
Discussion started by: tanpeng
6 Replies
2. IP Networking
I am am using IPv6 IP's with an OS of Debian.
Is it possible to set a *static* default gateway w/o the router being connected? Will that gateway change when the router is connected?
TIA (0 Replies)
Discussion started by: Meow613
0 Replies
3. Linux
Dear Sir
I am a newbie in the world of IP telephony. I have been working with Asterisk PBX (SIP) and Cisco Call Manager (MGCP) but now I am learning on how to work GNUGK for H.323 Gatekeeper.
I am having a problem, configuring static call routing on GNUGK
in the section
... (0 Replies)
Discussion started by: mfondoum
0 Replies
4. Solaris
Hi all,
Just now i had change the gateway for a server
Go to /etc/defaultrouter, change to 10.86.33.1
route delete default 10.86.39.222
route add default 10.86.33.1
now cannot telnet to the server already..
any idea? (5 Replies)
Discussion started by: SmartAntz
5 Replies
5. AIX
Dear folks,
How can delete the gateway from smitty or by command, Because I have 2 gatway in the system and I tried to delete by smitty it gave me failed command (7 Replies)
Discussion started by: magasem
7 Replies
6. Programming
how we can get the gateway address.
i know gethostname used for ipaddress
how we can get the system gateway address.
thank u inadvance,
sree (2 Replies)
Discussion started by: phani_sree
2 Replies
7. Shell Programming and Scripting
Hi,
I have a challenging task,in which i have to find the duplicate files by its name and size,then i need to take anyone of the file.Then i need to open the file and find for more than one pattern and count of that pattern.
Note:These are the samples of two files,but i can have more... (2 Replies)
Discussion started by: jerome Sukumar
2 Replies
8. Red Hat
Hi,
in which file and how shuold be decalred a gateway and its IP adresse ?
Where and how add a gateway ?
Many thanks before. (3 Replies)
Discussion started by: big123456
3 Replies
9. IP Networking
I used "route" to add the default gateway
I wrote this:
route add default 19x.x.x.x 0
but this is not permanent default gateway.
Do I need to use another command?
Thank a lot (2 Replies)
Discussion started by: lmena
2 Replies
10. UNIX for Dummies Questions & Answers
hi
i got a problem. I use a fbsd box to share my (DSL)internet connection.
I got 2 networkcards in my fbsd box, but my networkcard 1 (to my modem) always go out. the led don't burn anymore and I lose my connection to the internet :(
but my networkcard2 (to my local network) doesn't go out,... (2 Replies)
Discussion started by: Stormpie
2 Replies
ripquery(8) System Manager's Manual ripquery(8)
NAME
ripquery - Queries RIP gateways
SYNOPSIS
/usr/sbin/ripquery [-1] [-2] [-[a5] authkey] [-n]
[-p] [-r] [-v] [-w time] gateway ...
FLAGS
Sends the query as a version 1 packet. Sends the query as a version 2 packet (default). Specifies the authentication password to use for
queries. If -a specified, an authentication type of SIMPLE will be used, if -5 is specified, an authentication type of MD5 will be used,
otherwise the default is an authentication type of NONE. Authentication fields in incoming packets will be displayed, but not validated.
Prevents the address of the responding host from being looked up to determine the symbolic name. Uses the RIP POLL command to request
information from the routing table. This is the default. If there is no response to the RIP POLL command, the RIP REQUEST command is
tried. The gated daemon responds to a POLL command with all the routes learned through RIP. Used the RIP REQUEST command to request
information from the gateway's routing table. Unlike the RIP POLL command, all gateways should support the RIP REQUEST. If there is no
response to the RIP REQUEST command, the RIP POLL command is tried. The gated daemon responds to a REQUEST command with all the routes he
announces out the specified interface. Because of limitations in the UDP interface, on systems based on BSD 4.3 Reno or earlier, REQUESTs
respond about the interface used to route packets back to the sender. This can be avoided by running ripquery on the host being queried.
Displays version information about ripquery before querying the gateways. Specifies the time in seconds to wait for the initial response
from a gateway. The default value is 5 seconds.
DESCRIPTION
The ripquery command is used to request all routes known by a RIP gateway by sending a RIP request or POLL command. The routing informa-
tion in any routing packets returned is displayed numerically and symbolically. The ripquery command is intended to be used as a tool for
debugging gateways, not for network management. SNMP is the preferred protocol for network management.
The ripquery command by default uses the RIP POLL command, which is an undocumented extension to the RIP specification supported by routed
on SunOS 3.x and later and by gated 1.4 and later. The RIP POLL command is preferred over the RIP REQUEST command because it is not sub-
ject to Split Horizon or Poisoned Reverse. See the RIP RFC for more information.
RELATED INFORMATION
Commands: gated(8), gdc(8), ospf_monitor(8), routed(8) delim off
ripquery(8)